Search results

  1. brandon.colt

    Driveshaft spacer

    Okay. My ProComp lift came with a front spacer but not for the rear. When I crawl under the truck, it looks like the yoke has moved out of the t-case about an inch or two. Im trying to figure if thats safe or if I need to find a spacer for the rear driveshaft. Thanks for your input fellas.
  2. brandon.colt

    Driveshaft spacer

    Does anyone have a rear driveshaft spacer on their 6" lifted 1500?
  3. brandon.colt

    Grinding noise

    When I put the truck in drive and hold the breaks (power breaking), the rev the engine, starting around 1200rpm there is a faint grinding noise. I can't tell if its coming from the trans or transfer case. Anyone have any similar situations or knowledge on the matter? Thanks 2012 1500...
  4. brandon.colt

    Best $300 mod

    He was messing with you, the catch can does not add any hp. It is a good mod for keeping oil out of your filter and out of the combustion chamber though. Well worth it but you do need to empty it every 2-4k miles depending on how quickly it fills up.
  5. brandon.colt

    ***Clunking in the front end after Bilstein install ..***

    If the CV is binding up because of the new geometry induced by the lift, they can go to shit within 50 miles or less. I currently have a bad CV because of my lift, got new ones on the way. I have a lot of play on the inner where it goes to the diff. A little in and out play is okay (I think) but...
  6. brandon.colt

    Here's my plan, pick it apart....

    I'll give you my stats followed by my experience. 2012 Ram 1500 QC/RB 4x4 5.7 3.92 6" PrpComp lift w/ 2.75 MX6 adjustable coil overs 37" MT2 tires 18" wheels w/ -12 offset As far as fitting in the garage, that'll never happen again (for me) not even aired down. I installed the lift myself, I...
  7. brandon.colt

    ***Clunking in the front end after Bilstein install ..***

    CV axle
  8. brandon.colt

    Broken Manifold Studs?

    Ram should issue a recall on these trucks. My 2012 52k miles has at least one broken manifold bolt as well.
  9. brandon.colt

    Possible CV issues

    Anyone... Anyone... Bueller... Bueller...
  10. brandon.colt

    Possible CV issues

    So my passenger side CV inner joint is busted and needs to be replaced. Any recommendations for aftermarket CV axles?
  11. brandon.colt

    Who's rock'n a 6" lift with 17" wheels

    The issue with a quality lift and 17" wheels is the clearance between the inside of the wheel and the spindle.
  12. brandon.colt

    Can't get rear shocks out

    Buy a cheap wrench, take the box end and about 1.5" of the handle; cut everything else off. Slip it onto the nut and you're good to go.
  13. brandon.colt

    Possible CV issues

    Rzrman328, I've gone through you're build thread; very nice. I don't know how to upload pics, it asks for a URL. With that I have not taken picture under the truck. Jameson, The coils are set about half way through their adjustable range. That's how they arrived. Without pulling out a tape...
  14. brandon.colt

    Possible CV issues

    ProComp 6" part K2084BMX ProComp MT2 37x12.50/18 XD Monster 18"x9" -12 offset The tire does not make contact with the front or rear fender well going right or left lock to lock on either side.
  15. brandon.colt

    Possible CV issues

    Anyone have binding in their CVs while turning after lifting their truck? How did you fix this? If you replaced your CVs, where should I look?
  16. brandon.colt

    How are the Mevotech UCA's holding up?

    My decision to run mevotech was because there are plenty of positive reviews and the next option is around $300 more expensive.
  17. brandon.colt

    How are the Mevotech UCA's holding up?

    I have a set of mevotechs for my 2012, they came together in one box with no paperwork, info, or anything. How can I know which side is for driver and which for passenger? thanks
  18. brandon.colt

    Rear shocks... What's the point?

    Lets assume one doesn't carry a heavy payload, tow, or off road on a regular basis. What is the point of bolting on fancy shmancy shocks i.e. Fox, Icon, King, and the like when there's virtually no weight on the rear end? I'm not bashing anyone who has gone this route, Just looking for...
  19. brandon.colt

    Any regular cab Rams with 6" lift?

    I still think lifted RC/SB trucks look better than any other cab configuration out there. My first truck was a RC ranger, then moved up to a RC Ram 1500, in a QC Ram 1500 now, next will be a 2020 CC/LB Ram 3500. Then when I'm old and the kids are grown I'll prolly go back to a RC Ram.
  20. brandon.colt

    Where do I even start?

    http://www.procompusa.com/suspension-product-details.aspx?pt=3533&pl=1808&pqq=2281&pqa=13199
  21. brandon.colt

    Where do I even start?

    http://www.procompusa.com/suspension-product-details.aspx?pt=3533&pl=1808&pqq=2281&pqa=13197
  22. brandon.colt

    Tow hookd

    You'd have to remove and modify the black plastic piece between the fog lights. That should be all that's needed other than the tow hooks and eight bolts.
  23. brandon.colt

    3.55 gears. Want to run 37's will I be ok?

    If I were in your shoes I would start at junk yards looking for 4th gen 4x4's with factory 3.92s. If you can change spark plugs and do an oil change, you can swap gears. If you found factory 3.92s in good condition you'll save hundreds perhaps a grand by going this route. If money isn't a...
  24. brandon.colt

    ProComp UCA's

    Anyone have experience with ProComps UCA's for their 1500?
  25. brandon.colt

    Coal Rollin' LOL

    I don't know, you said "diesel assholes" like me. I don't have a diesel.

Latest posts

Staff online

Members online

Total: 519 (members: 17, guests: 502)
Robots: 1,654

Forum statistics

Threads
195,697
Posts
2,873,409
Members
156,572
Latest member
Joey93

Share this page

Top