Two wires should have been separated. One to pdc and the other to a ground. Remaining go through firewall. It's personal preference whether to go through the rubber boot for main wiring into cab or to drill a hole through the cover plate for clutch to the left. I went through the cover plate...
If you search in the 4th Gen DIY forum you will find a thread about oem footwell lighting. I just installed this in my regular cab. I bought the oem led lights and bezels. The thread starts out on how to stick them in place with double sided tape but you don't need to do this if you buy the...
When you say nothing works do you mean radio doesn't work either? If the radio won't come on you may have depopulated needed wires on connector to radio that power up everything. When reading instructions with camera kit it can be confusing where the 3 wires terminate on radio connector. When...
The uconnect 3.0 to 5.0 upgrade is finally finished. I routed the wiring header to the oem mirror with microphone and installed the evic switch with v/r and phone buttons on the steering wheel. While I had the glove box out I went ahead and installed the oem footwell lighting on passenger side...
I know some of you guys have done this and need some input. I'm trying to route an oem wiring header for oem manual mirror with microphone. I wasn't expecting existing wiring where I need to plug in all the straps for new header. It looks like the existing wiring has something to do with air...
How are you guys turning the steering wheel to get the airbag clips loose? I tried turning my wheels on finished concrete floor in garage while engine off and it feels like I'm going to break something before the wheels move. Are you putting sand under the wheels or doing this mod in the yard on...
Remove two screws at bottom of kick panel and grab below steering column and pull.
The housing is the outer part of the connector. If you look at photo above you can see where the connector has one small hump on the side and the housing has a square opening where the hump slides into. Separate...
It is the hardest part of the install. The only way I could do it was to slide a workout bench over to the driver side to hold my romp up as I lay on my right shoulder. I also detached the driver side kick panel and one connector to it. I left the hood release attached and slid the kick panel...
I believe that is what I'm talking about. You have to remove it to depopulate pins correct? Thanks for the links. I may buy one and the next time I have my radio out I'll replace it.
You're welcome.
If anyone out there that knows how to take the red face plate off of radio connector without breaking it please give advice. It might help others. I broke mine into 3 pieces. I snapped them back on even though they were broken without issue.
It was confusing for me to where the pins went until I saw an image I think that is earlier in this thread showing exactly where they go from the rear. The diagram in kit instructions made me think I had to depopulate some existing wires which was wrong. If you look at rear of connector it is...
I used a small pick that is the size of a pocket screwdriver to depopulate pins. They come with some screw driver sets. This one has a bent end but the straight one will do also.
More than likely the tailgate harness is there but the body harness going from rear to front isn't. You can tell by looking under the rear of the truck just slightly to driver side of spare tire. Just follow the existing body harness up to where it connects to tailgate harness. If you just see...
The strange thing is that I already had the connectors installed at factory. I do have a locking tailgate. I also replaced all of it when I installed the oem backup camera kit.
I don't know if this helps any but when I had my 2014 Ram Express serviced the first time the Dealer threw in this bag of parts in my dash. It happens to be the tailgate and body harness connectors. I have no idea why this would have been a service bulletin or recall but anyway the bag has a...
I know this thread is about audio controls but is there instructions somewhere on how to replace evic switch with one that has v/r and phone buttons? Thanks, Nick
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.