Recent content by ErickTAR21

  1. ErickTAR21

    CLUNK after Eibach Level and Alignment

    Youre 100% right, I borrowed two sets from advanced auto when i put it in, i still have them for some reason. But I really dont want to mess with that again. Before i do, ill have my wife re-create the issue on a slow left turn into my driveway and feel up there for a pop.
  2. ErickTAR21

    CLUNK after Eibach Level and Alignment

    I was hoping since it came up after the alignment it was something related to it. But yea I remember how hard it was tightening that bolt. I'll have to take that whole side apart again. IF thats not it then IDK i might just ride it till it breaks. Im just worried the issue is with the steering...
  3. ErickTAR21

    CLUNK after Eibach Level and Alignment

    WELL, I just hand/ratchet checked most of those, except the driver side top center strut bolt, I eyeballed/fingered that AND the it is 1 1/2 - 2 threads "less threaded" than the passenger side strut. FUuuuuuuuck, I guess i know what I'm doing sometime this week. Question, does tightening that...
  4. ErickTAR21

    CLUNK after Eibach Level and Alignment

    1. That sucks, I have to take off the strut assembly to do that. 2. The clunk came after the alignment, not after the install. So I kinda ruled out the strut assembly (coilover?), was that a wrong assumption?
  5. ErickTAR21

    CLUNK after Eibach Level and Alignment

    I also thought it might have been the sway bar links by the looks of their "angle" so i removed both the front sway bar end links and it didnt do anything but make my truck LEAN in turns lol. Did you give that a try?
  6. ErickTAR21

    CLUNK after Eibach Level and Alignment

    I checked all related nuts/bolts with the level after I did it, and I checked behind the shop after the alignment. Since thats when the noise decided to show up. Also the ball joints look good.
  7. ErickTAR21

    CLUNK after Eibach Level and Alignment

    Little back story. I got the eibach kit (front shocks&springs and rear shocks&springs) and installed it myself (never again). I drove it for maybe 500 miles before I got it aligned, no issues up to this point. Drove great and straight so I put it off for a couple weeks. The truck was toe-d in...
    • ErickTAR21
    • Thread
    • clunk eibach lifted ram
    • Replies: 14
    • Forum: Lifted
  8. ErickTAR21

    Eibach Pro Lift Kit

    I just installed the Eibach Kit, Springs and Struts on the front and rear and my Measurements are 39" up front and 40" on the back. Measurements were taken at the apex of the fender flares. I do have fender flares so they take up about an 1/8 of an inch off the measurement. I have a 2017 Laramie...
  9. ErickTAR21

    Slow shift from 1 to 2 when cold

    Next time try turning on Tow/Haul as soon as you turn your vehicle on and keep it on for your first mile or two of driving. Thats what I do and it seems the different shift points set by tow/haul mode alleviate the "awkward" first shifts on startup.
  10. ErickTAR21

    Ac compressor clutch

    There is a lot of room up front there. Could you not remove the fan and fan shroud, giving you enough space to get a puller to pull out the clutch assembly and replace JUST that? You'll have to buy a whole separate compressor if you cant find just the clutch assembly, but you can get one online...
See more

Latest posts

Staff online

Members online

... and 6 more.
Total: 1,388 (members: 56, guests: 1,332)
Robots: 1,936

Forum statistics

Threads
195,648
Posts
2,872,883
Members
156,483
Latest member
Jayhull82

Share this page

Top