Recent content by frederic noel
-
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
do you have the oem camera or aftermarket ? mine is aftermarket so dunno if the box will activate it , mine is wire thru the signal 31-32 pin , it should work imo ?- frederic noel
- Post #3,607
- Forum: 4th Gen DIY
-
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
thnx man , i'm gonna wait till they showed up to see if they done something to get the Bu cam work- frederic noel
- Post #3,602
- Forum: 4th Gen DIY
-
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
hey guy's i'm looking for some answer , i have an aftermarket back up camera that is working fine with my previous radio RA2, than i switch to a VP4 , but now i have a 4c and when i put in reverse ( truck is manual ) the screen don't switch, i have to manually press the backup camera icon to...- frederic noel
- Post #3,600
- Forum: 4th Gen DIY
-
How to Add Automatic Temperature Control (ATC) to a Manual Temperature Control Truck
mdtz86 i have similar issue , i did the mtc first and everything work fine , blend door in the right place etc.. i did the atc upgrade with temp sensor ( mine is a 3500 ) put an atc bezel, do the procedure etc.. everything went ok , in auto mode the blend door look to be in a defrost state...- frederic noel
- Post #981
- Forum: 4th Gen DIY
-
INFO - 2013-2018 8.4A /AN FW Notes (RA3/VP3-NA & RA4/VP4-NA & UAx)
hey guy's i've done the 5 inch to 8.4 radio conversion with the single zone atc , my question is , when truck is cold , in the winter , i can't get the blend door to the right setting , defrost on defrost etc... but when temperature is in normal operation , everything work as it suppose to, i...- frederic noel
- Post #1,506
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
yep it is showing now- frederic noel
- Post #1,805
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
i have the 7 inch , i will definitely turn that passive entry on and see if work , thnx doug- frederic noel
- Post #1,804
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
maybe that was it ,first pin was the number 2 etc.. i did not pay attention to the empty spot, as of my evic message that don't appear do you guy's know what it need to be set ? im with the latest version of alfa and obdlink mx+- frederic noel
- Post #1,801
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
at the beginning of thread it write that the pin 1 and 11 are no connect that it is false on my rf hub , pin 1 and 11 is antenna 4 ( front ) and pin 2 and 12 is for antenna 3 ( back of truck ) other are not connected because , i don't need the passive entry , and as for my evic , i think alfa is...- frederic noel
- Post #1,798
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
yes it working , the diagram for the pinout at the beginning of thread was not right , and mine doesn't show press clutch + start but it work like it suppose too , everything work fine , but i'm sure because of android 12 that came up , alfaobd app it a little glitchy- frederic noel
- Post #1,795
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
other thing i see in the alfaobd app is usually when i change something in some option it is showing ( procedure complete ), but when i select keyless go and select to YES, it is showing YES almost instantly , if i select NO and press start ( procedure complete ) is not showing but if i select...- frederic noel
- Post #1,790
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
is it possible that my 2 keyfob were not working ?( the key was purchased from amazon and i checked the battery to ) when im in the truck and press unlock it will wake up the cluster for a few second , is a sign that the key are working ? , but i cannot still figuring how to program it- frederic noel
- Post #1,789
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
i checked just before the swap , and everything was setup fine except for passive entry that i did not enable , i even switch wire thinking i put in wrong terminal , and still no go ? each time i try to program the keyfob i have the message , transfer secret key from bcm to rfh failed , but if i...- frederic noel
- Post #1,788
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
hey guys just finishing installing , the 2 antennas , rf hub and pts , i disconnect both battery , reconnect everything , when i open the door , i see nothing on cluster ? suppose to see the clutch + start display , but none , i try to program key and it failed for both , i have this message...- frederic noel
- Post #1,786
- Forum: 4th Gen DIY
-
Members online
- Wild one
- sigfla
- Black1500Ram
- Dredger
- Jeepwalker
- DILLIGAF
- amadhi89
- Daman
- Spankie
- Shirokez
- AllMoparParts.com
- Bmags
- Dodge 1500 4X4
- OutlawFMX
- BigTex2500
- Marshalljud
- 4xdad
- 21SilverRam
- EriikK
- Uncle Sam
- Masten
- kdb777
- JonathanSorensen
- Luke787
- Loudram
- Akaras3
- Slinge
- ZebEllison
- hhhjohn
- gopokes86
- JHoward
- tron67j
- MOGG
- SJP_1809
- SoFLRam
- Quick_Shifter
- Westwind1124a
- VikeFan
- Mb7640
- MWP1500
- CalifPhil
- HuskerRam
- andres124501
- Lsujker
- Ramfanski
- JW2 Innovations
- AZ MARK
- KWal
- mb33458
- PigPenCO