Search results

  1. rebel89820

    Tranny dumping fluid out at inspection plate on bell housing?

    Hello everyone... first post in a while. I have a 2001 1500 4x4 with 5.9 and 46re (?) So after some pretty hard mudding my transmission is pouring fluid out the front of the bell housing as fast as I can put it in. I've been told that the seal between TC & transmission has failed, which makes...
  2. rebel89820

    Some really DIRTY pics

    Had a pretty "dirty" weekend... I haven't ever been stuck this bad before. My son was in town for the weekend & decided to go on a coyote hunt in his grandpas stock half ton 4x4. He decided to head for home when the worst rain storm this area has seen in years parked on top of them. This is my...
  3. rebel89820

    2wd suspension lift??

    So my son is graduating from high school on Friday and all he has asked for is a good lift kit for his 98 QCSB 5.9 2x4. We put a cheap spacer and block system on last Christmas but it caused alot of front end trouble so im looking for a quality replacement. Fabtech used to make a 6.5 inch that...
  4. rebel89820

    Shock Limit Straps... ??

    Anybody running them or have any opinions on them? The guy I bought my shocks from at 4wheelparts swears up and down that I need them. He has a valid point.... even if I don't INTEND to air out the suspension or anything crazy like that.... it COULD happen [emoji41] and for 20-40 bucks, I...
  5. rebel89820

    Looking for Kenwood Bluetooth...

    I need the Bluetooth kit for a Kenwood head unit... part # KCA- BT300. willing to pay or trade some really good stuff if anybody has one to get rid of...
  6. rebel89820

    Fs/ft vision x led's

    2 each "Ripper" 12 bulb 60° beam... $300 each obo 2 each "Solstice Prime" 5 bulb 40° beam $200 each obo Each box has one light, one wire harness w/ relay, one switch and mount bracket with everything you will need to put these on pretty much anything with an engine... they're good from 9v...
  7. rebel89820

    Pinion bearing sizes...

    Well here I am 2 weeks later and still can't get the slop out of the pinion. Getting ready to pull it out AGAIN so I'll take some pics to post up. My question... are pinion bearings the same size on a thick cut 4.56 as on the stock 4.10's? I was under the impression I had 4.10 when I ordered...
  8. rebel89820

    Where did you mount your 12v switches?

    Prerunner / light bar should be back from powder coat soon... trying to decide where to mount switches for the 10 LED lights. Anybody willing to post up some pics of theirs? Sent from my DROID RAZR
  9. rebel89820

    Rear end kickin my rear end!

    01 1500 off road... pinion bearing crapped out on way home from hospital, had to pull the drive line and limp last 50 miles on the front axle. Got it home with no issues and started tearing it down. I had a master install kit from summit, and new clutch packs from Spicer for the LSD... Got it...
  10. rebel89820

    Measurements??

    Hey guys, would anyone have the time to grab a quick measurement for me? Working night shift & going to start over on my light bar... I have them all but left my notes in my truck at the bus stop... I just need the front bumper from center to either side where it bends, then from the bend to the...
  11. rebel89820

    Any ideas? Son wants this 15" in back of his 2nd gen...

    Sent from my DROID RAZR
  12. rebel89820

    Another new guy here...

    Hey everyone, new member from Nevada here. I'll be getting some better pics up soon as it stops snowing/ raining long enough to wash the poor thing lol. Until then, here a few from last month.. since then it has new 35's on the same 16's in these pics. Really wish I would've went 37, these still...

Latest posts

Members online

Total: 424 (members: 11, guests: 413)
Robots: 1,464

Forum statistics

Threads
195,697
Posts
2,873,409
Members
156,572
Latest member
Joey93

Share this page

Top