Search results

  1. R

    Urgent Help Needed Seeking Discontinued Transmission Harness 2014 6.7l 3500 Aisin

    Do a search on car-part.com. They have a few in California junk yards with the part number that you're looking for.
  2. R

    Locker issue

    Check to see if your sway bar disconnects. If not, it's most likely an issue with the Final Drive Control Module (FDCM) on the front sway bar. It controls the sway bar disconnect and both the lockers. Pull the connector off and see if there is corrosion in the connector. Sometimes you can clean...
  3. R

    Need belt diagram help for 2017 2500 6.4 single alternator.

    Here's the diagram out of the shop manual.
  4. R

    Bad Body Mounts?

    Here's the factory instructions....
  5. R

    Fuel Pump wire to TIPM diagrams

    Here's the diagram for the fuel pump. There aren't any blue wires in the power control, but it looks like it might be the dark brown/orange next to the blue wire.
  6. R

    Another p0456

    You need to hook up a smoke machine to find where the leak is.
  7. R

    2016 6.4 died while idling…PLEASE HELP!

    I saw where you said they put in a throttle body, but didn't see where you mentioned the cam and crank sensors. Probably going to be a wiring problem.ĺ
  8. R

    2016 6.4 died while idling…PLEASE HELP!

    A bad camshaft sensor could cause this. I have seen them in the past where they run a little bit, then short out and open all the injectors and continuously fire all the coils. Floods the engine and fries the coils. Quite the mess. Less likely a crank sensor, but possible. Need to get a...
  9. R

    Help with break bleed?

    You need to do another standard bleed after doing the ABS. Here's from the shop manual; STANDARD PROCEDURE - ABS BRAKE BLEEDING ABS system bleeding requires conventional bleeding methods plus use of a scan tool. The procedure involves performing a base brake bleeding, followed by use of the...
  10. R

    Power outlet circuit location

    You can see in the wiring diagram how the power is provided by which slot you have it in, 90 or 91. That power is routed either to the back of a center console or to the power block inside the fold down center armrest. Since a 2018 Power Wagon doesn't have the center console it's the block in...
  11. R

    Power steering return hose 5154881AA

    You may have to go to a custom builder https://westadamsradiator.com/custom-hoses.html
  12. R

    Bouncing on certain interstates with stock tires

    I have the same issue In Colorado with the concrete roads. I concur with the above. I run tire pressures at 40/35, but the biggest difference was made when I changed the stock Bilstein 4600 shocks. I tried the 5100 shocks first and that helped quite a bit, but when I upgraded to the Thuren...
  13. R

    front face emblem camera

    This is one...... https://tailgatecamera.com/products/ram-front-emblem-camera?variant=6714606092327
  14. R

    2014 3500 leaf springs

    Go to www.car-part.com if you want a used one. They show hundreds available with several in Florida.
  15. R

    2012 Ram 2500 Cummins HD HO suspension/handling issues

    This has all the symptoms of a worn or loose track bar. If the bushings are shot or the bolts are loose, the axle can actually move and cause the thump you are hearing in addition to the poor steering. If you remove the track bar for inspection, the torque on the bolts is 200 ft. lb. when...
  16. R

    66rfe rattling noise

    More than likely one of the flex plate or torque converter bolts has loosened and is hitting in there. I can't remember if there is an inspection access plate that you can remove and look in there. I wouldn't drive it much more before you get it into a shop.
  17. R

    AMP Power Steps for 2500 Diesel Installation

    Yes, you have to install the rivnuts first ( unless they're already installed from the factory). Loosen the arm bolts and the pinch weld bolts slightly. You want the arms to move down when you put your weight on the step.
  18. R

    AMP Power Steps for 2500 Diesel Installation

    Mount the hinge arms first. Do not install the rivets or the motor. Install the step onto the arms. Manually move the step up and down to check for any clearance issues. If you have minor rubbing on the pinch weld, loosen the bolts on the arms a little and then put your weight on the steps...
  19. R

    Hub-centric Spacers on Stock Wheels for 37s

    I run these spacers in the winter time if i need to put heavy chains on. It gives me the clearance I need. I've never had an issue with them...
  20. R

    2019 PW Torque specs for Front disconnecting sway bar frame mount bolts

    The shop manual shows 43 ft lbs.
  21. R

    2012 3500 Limited Dually Jack and Jackstands

    If you have a Harbor Freight close by, their Daytona Floor Jacks are very good, I have two of them and used them to lift both ends of the truck while doing suspension work. The jack stands listed by Mister Luck are very good also...
  22. R

    Dpf fed up

    You can get an Edge Monitor. It monitors all the main diesel parameters (regen, EGT's, etc.) and allows the user to initiate a regen cycle. https://www.edgeproducts.com/products/in-cabin_monitors/parts/84130-3
  23. R

    No power to fuel pump

    Here's the wiring diagram. There's another relay and a fuse in addition to the fuel pump relay.
  24. R

    What's New and Used Mile's

    Limit in Colorado is 1500 miles. According to Code of Colorado 1 CCR 205-1, Regulation 44-20-102(20); For all motor vehicles except those classified as a “motor home,” as defined in section 24-32-902(7), C.R.S., a “new motor vehicle” is a motor vehicle that has been transferred on a...
  25. R

    Winch Solenoid Pack

    Since you already have the solenoid out, you could clean the terminals then protect them with a electrical connector sealant such as...

Latest posts

Staff online

Members online

... and 3 more.
Total: 1,389 (members: 53, guests: 1,336)
Robots: 1,964

Forum statistics

Threads
195,648
Posts
2,872,892
Members
156,483
Latest member
Jayhull82

Share this page

Top