Search results

  1. S

    Just got an alignment at the dealer, please check my print out for me?

    Today's print out. They said something is wrong it won't hold alignment.
  2. S

    Just got an alignment at the dealer, please check my print out for me?

    Dodge dealer, and everything is brand new up front including tires and I did the work my self so I know it's done right.
  3. S

    Just got an alignment at the dealer, please check my print out for me?

    What did you do?
  4. S

    Just got an alignment at the dealer, please check my print out for me?

    I don't wanna deal with them again, I spent 3hrs there. They said it's in spec.
  5. S

    Just got an alignment at the dealer, please check my print out for me?

    I did a lot off front end work, I scribed factory locations to get it all close to spec. Got new tires put on and it drove fine but I didn't wanna risk tire wear so I brought it to the dealer to be aligned and during the ride home it's pulling right, steering wheel isn't centered, I have to...
  6. S

    Finally got around to installing my tracloc.!

    Wasn't to bad, I used my original gear set and just swapped to tracloc from my open carrier. Installed new bearings and cleaned everything up.
  7. S

    Faded plastic

    Magic eraser then back2black.
  8. S

    Anti-spin install guide?

    Sorry, the pdf file is to large to post. I'm not sure how to select sections from the file.
  9. S

    Anti-spin install guide?

    Hope this helps! The adjusters have to be backed off, possibly only one side will do.
  10. S

    Started my plenum repair, what a pain!

    Thanks, it's the factory box for a 5.9l with a K&N filter.
  11. S

    CV axle question for the guys Drag racing 4X4's

    I'm pretty sure the cv axle is what holds the hub bearings together, someone on here did that and the hub bearings fell apart. Might want to verify B4 go any further.
  12. S

    Started my plenum repair, what a pain!

    Got it all back together! Can't wait to fire it up....
  13. S

    Started my plenum repair, what a pain!

    Well I got them out by letting them sit overnight soaked in PB, I heated them up real good, clamped a new pair of vise grips on, sprayed PB on it right after removing the heat, just worked back and forth the both came right out.
  14. S

    Started my plenum repair, what a pain!

    The 5.9 was losing 2 quarts in 800 miles, valve covers were leaking to. I got everything torn down, I fought the most with the stupid plug wire holders that go over the valve cover bolts.....now I'm trying to get the two front broken bolts out of the head from the intake, they broke off at the...
  15. S

    Replaced my junk rear diff today!

    Thanks, it sucks with an open diff. For some reason my 4x4 works great now though, disengages fine, doesn't pull all over the road. All from the bad rear diff? Does anyone no if you can put clutch packs and spiders in an open carrier to make it anti slip?
  16. S

    Replaced my junk rear diff today!

    Mine was making all kinds of nasty sounds, bad pinion bearings and axle bearings so far not sure what else. I found a decent one from the junk yard, had to remove it from the vehicle and load it up. Got home and pulled my old one out and put in the used one. Took me most of the day but it's nice...
  17. S

    Headlight alignment

    25ft, that's what I used to adjust mine!
  18. S

    Under seat sub enclosure

    Foxacoustic.com....I heard great things about there enclosures. I went with jl audio center council sub cause it was used locally for a good price.
  19. S

    Post a Pic of Your Ram in its Spot

    Just got her 3 weeks ago... :buffer:
  20. S

    Do you wax or seal?

    I do both, sealer Is used to seal in your work aka compounds, polishes. Wax is used to protect your sealer.
  21. S

    Door harness repair/ no speakers,locks, illumination, rear doors.

    thanks, this place has been a big help with lots of information!
  22. S

    Door harness repair/ no speakers,locks, illumination, rear doors.

    so i got around to inspecting the rear door harness today, there were alot of broken wires. i removed the hole harness from the truck so i could get to everything. had to depin 2 connectors that broke off. both side were really bad just moving wires they were braking. shes back together now and...
  23. S

    2002 ram fuse box wiring/ fuse #51 help please...

    Well I figured it out, the pink wire in pin #16 obd port is the power lead witch ties into everything for fuse #51. That wire is #9 in the green plug for fuse box, it's was corroded and broke off the pin. All is good now!
  24. S

    Radio doesn't power on

    Did you ever find a solution?
  25. S

    2002 ram fuse box wiring/ fuse #51 help please...

    I just purchased a 2002 ram 1500 quad 5.9 4x4, no power to anything with key off. I Checked all fuses, pulled every plug from fuse box and clean the pins. Looked at wire harness and can't figure it out. Fuse 51 is good, I've search for 2 weeks and can't figure it out, there is also no radio or...

Latest posts

Members online

... and 10 more.
Total: 1,249 (members: 60, guests: 1,189)
Robots: 1,812

Forum statistics

Threads
195,643
Posts
2,872,847
Members
156,477
Latest member
djmwilliams11

Share this page

Top