NOTW
Senior Member
I found this on another site and thought it would be useful here. Since this is not Ram generation specific, I really didn't know where to put it...
In-Dash DVD Video Bypass Procedures
JENSEN
-Flip (most models) Tested and works on all Phase Linear:
(on remote)
1)Hit Setup On Remote.
2)Select Language. ---------------------(if it doesnt work try not hitting language)
3)Get Remote And Hit 5,4,3,2,1,0. Listen For Beeps.
4) Touch “Hammer/Screwdriver” Logo. (new logo)
5)Select Brake Override
6)Switch To Brake Override “ON”
7)Now Hit Setup On Remote.
8)And Now Watch Movies.
DUAL
-Flip Screens:
Ground parking brake wire
(on remote)
1) Hit stop then stop again.
2) type 26604 then press Enter
3) this sequence must be done when a dvd is in the drive. Wait for dvd audio then do sequence.
PIONEER
General Pioneer Relay Mod
Use a standard 4 pin relay. Pin #86 and #87 both to ground. #85 remote wire from headunit.
#30 parking brake wire from head unit
-AVIC-4000DVD:
1)Must use switch (on off on) or PAC TR-7, no other bypass available
-AVIC-D3:
1) Remove Mute wire on pre-out harness and move pin directly below to the open slot and wire to ground
2) Ground parking brake wire.
3) Hit {OK} on the pop up message stating Driver viewing of video signal while driving is Illegal.
4) Bypass should be done and working.
-AVIC-N1:
1) ground the brake wire
-AVIC-N2:
1) solder 2 pins underneath the silver warranty sticker on the unit itself
-AVIC-N3:
1) Under silver warranty sticker on underside of unit is a switch
2) CAREFUL this sticker over the switch is a void tansparent sticker so do so only with customer permission.
-AVIC-Z1: (not tested)
1) you have to turn on and off your parking lights (illumination wire must be connected) when the unit first boots up.
-AVIC-D1 and D-2:
1) put a pin into the empty slot next to the ground wire on the pioneer radio harness and ground it.
-AVIC-F Series (700BT & 900BT):
1. On the white harness (the Pioneer Installation Instructions refer to this as the “RCA Connector”), find the mute wire (yellow/black). It is originally in the “1” position. Lift the plastic tab of where it is inserted into, pull the wire out, then place it into the “4” position on the bottom. It should now be in between 2 black wires.
2. On the black harness (the Pioneer Installation Instructions refer to this as the “Power Cord”), find the parking brake wire (light green). Ground the newly placed mute wire (yellow/black) from the “RCA Connector” and the parking brake wire (light green) from the “Power Cord”. Some folks suggest grounding to something other than the main ground. Not sure why, but if that’s doable, you should. Some folks believe grounding onto the main ground of the radio is fine. The following pictures show this setup ground to the main ground. The first picture shows the parking brake wire (light green) and the mute wire (yellow/black) connected to a light green wire. The second picture shows that light green wire running to and spliced onto the main ground.
ALPINE
-IVA-W200:
1) PAC TR-7 Bypass module defeats pulse sequence needed between foot brake and hand (e) brake. PAC instructions are as follows:
Black – chassis ground
Red - +12volts switched power
Green – Alpines remote turn on (+12volt)
Blue – Alpine’s footbrake
White – Alpine’s parking brake
DO NOT CONNECT the parking brake or footbrake wires to the vehicle. Connect directly to the TR – 7. It should come preprogrammed to version 2, so make sure the programming switch is in the off position
KENWOOD
-KVT 617 DVD (flipout):
1)Ground parking brake wire
-KVT 512 DVD (flipout)
1)Ground parking brake wire
-KVT 512 DDX (double din)
1)Ground parking brake wire
JVC
-KDAVX44 (Single Din Touchscreen)
1)Ground parking brake wire
-JVC-KD-AUX2
Ground parking brake wire
-JVC KW-AVX710
Just ground the e-brake wire.
Disclaimer: It is illegal to have any of these installed on a road-use vehicle, by doing these, you fully understand that you are breaking the law, and you can get a ticket. Please use safely. I do not take credit for finding these bypasses, these are all bypasses I didnt pay for there for sharing the info with everyone else.
__________________
In-Dash DVD Video Bypass Procedures
JENSEN
-Flip (most models) Tested and works on all Phase Linear:
(on remote)
1)Hit Setup On Remote.
2)Select Language. ---------------------(if it doesnt work try not hitting language)
3)Get Remote And Hit 5,4,3,2,1,0. Listen For Beeps.
4) Touch “Hammer/Screwdriver” Logo. (new logo)
5)Select Brake Override
6)Switch To Brake Override “ON”
7)Now Hit Setup On Remote.
8)And Now Watch Movies.
DUAL
-Flip Screens:
Ground parking brake wire
(on remote)
1) Hit stop then stop again.
2) type 26604 then press Enter
3) this sequence must be done when a dvd is in the drive. Wait for dvd audio then do sequence.
PIONEER
General Pioneer Relay Mod
Use a standard 4 pin relay. Pin #86 and #87 both to ground. #85 remote wire from headunit.
#30 parking brake wire from head unit
-AVIC-4000DVD:
1)Must use switch (on off on) or PAC TR-7, no other bypass available
-AVIC-D3:
1) Remove Mute wire on pre-out harness and move pin directly below to the open slot and wire to ground
2) Ground parking brake wire.
3) Hit {OK} on the pop up message stating Driver viewing of video signal while driving is Illegal.
4) Bypass should be done and working.
-AVIC-N1:
1) ground the brake wire
-AVIC-N2:
1) solder 2 pins underneath the silver warranty sticker on the unit itself
-AVIC-N3:
1) Under silver warranty sticker on underside of unit is a switch
2) CAREFUL this sticker over the switch is a void tansparent sticker so do so only with customer permission.
-AVIC-Z1: (not tested)
1) you have to turn on and off your parking lights (illumination wire must be connected) when the unit first boots up.
-AVIC-D1 and D-2:
1) put a pin into the empty slot next to the ground wire on the pioneer radio harness and ground it.
-AVIC-F Series (700BT & 900BT):
1. On the white harness (the Pioneer Installation Instructions refer to this as the “RCA Connector”), find the mute wire (yellow/black). It is originally in the “1” position. Lift the plastic tab of where it is inserted into, pull the wire out, then place it into the “4” position on the bottom. It should now be in between 2 black wires.
2. On the black harness (the Pioneer Installation Instructions refer to this as the “Power Cord”), find the parking brake wire (light green). Ground the newly placed mute wire (yellow/black) from the “RCA Connector” and the parking brake wire (light green) from the “Power Cord”. Some folks suggest grounding to something other than the main ground. Not sure why, but if that’s doable, you should. Some folks believe grounding onto the main ground of the radio is fine. The following pictures show this setup ground to the main ground. The first picture shows the parking brake wire (light green) and the mute wire (yellow/black) connected to a light green wire. The second picture shows that light green wire running to and spliced onto the main ground.
ALPINE
-IVA-W200:
1) PAC TR-7 Bypass module defeats pulse sequence needed between foot brake and hand (e) brake. PAC instructions are as follows:
Black – chassis ground
Red - +12volts switched power
Green – Alpines remote turn on (+12volt)
Blue – Alpine’s footbrake
White – Alpine’s parking brake
DO NOT CONNECT the parking brake or footbrake wires to the vehicle. Connect directly to the TR – 7. It should come preprogrammed to version 2, so make sure the programming switch is in the off position
KENWOOD
-KVT 617 DVD (flipout):
1)Ground parking brake wire
-KVT 512 DVD (flipout)
1)Ground parking brake wire
-KVT 512 DDX (double din)
1)Ground parking brake wire
JVC
-KDAVX44 (Single Din Touchscreen)
1)Ground parking brake wire
-JVC-KD-AUX2
Ground parking brake wire
-JVC KW-AVX710
Just ground the e-brake wire.
Disclaimer: It is illegal to have any of these installed on a road-use vehicle, by doing these, you fully understand that you are breaking the law, and you can get a ticket. Please use safely. I do not take credit for finding these bypasses, these are all bypasses I didnt pay for there for sharing the info with everyone else.
__________________
Last edited: