plenum leak?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

johnnyjb

Member
Joined
Mar 10, 2012
Posts
59
Reaction score
1
Ram Year
2000
Engine
magnum 5.2
I've done searches but I'm curious if I'm not burning oil than I don't have a,leak right ?
Just checking before I get my sct tuner.
And do I need to get the 180 degree thermostat right away or later
 

talon6

Senior Member
Joined
Jul 1, 2010
Posts
1,180
Reaction score
28
Location
ohio
Ram Year
2002 QCSB 4X4
Engine
supercharged 5.9
i would get the 180 right away. it will help you not to "ping".

usually blowed plenum means oil usage. and if its not blowed now, it will. mine was blowed at 50k.
 
OP
OP
johnnyjb

johnnyjb

Member
Joined
Mar 10, 2012
Posts
59
Reaction score
1
Ram Year
2000
Engine
magnum 5.2
just hit 50k.
i dont burn oil.
Is there a recall for it?
 

ramthis9501

Senior Member
Joined
Jul 25, 2010
Posts
2,939
Reaction score
31
Location
Oklahoma
Ram Year
2001
Engine
5.2 V8
Looked through the throttle body blades with a flashlight to see if there is oil in there. If there is, your plenum is blown.

Here's my full DIY thread from when I did it to mine awhile back.

First off, take off the intake or air breather box, whichever you have.
2011-07-25_19-29-25_157.jpg

Next: disconnect battery (should've done it first...)
2011-07-25_19-29-54_936.jpg

Then remove the wiper fluid and coolant boxes along with the fan shroud and radiator. 4 bolts for the shroud and 2 for radiator.
2011-07-25_19-50-07_357.jpg
2011-07-25_19-50-12_749.jpg

Next take the drive belt loose
2011-07-25_20-02-36_969.jpg
2011-07-25_20-18-56_0.jpg

Then remove 4 bolts for A/C compressor (pic is after it's removed) And take loose two connectors off of it. A bracket will come out with it, it sits on top of the compressor.
2011-07-25_20-18-56_0.jpg

Move compressor to the passenger side fender
2011-07-25_21-11-51_361.jpg

Next remove the altenator (2 bolts) and 2 connecters
2011-07-25_20-24-59_86.jpg

After that remove the accessory bracket (5 bolts) one bolt is underneath a pully. Just remove the pulley and you can get to it easily.
2011-07-25_20-34-11_542.jpg

Then remove the heater hose and coolant hose. The coolant hose goes to the thermostat.
2011-07-25_20-51-40_120.jpg

Next remove the injector lines
2011-07-25_21-04-40_365.jpg

Remove the throttle cables
2011-07-25_21-04-26_512.jpg
 

ramthis9501

Senior Member
Joined
Jul 25, 2010
Posts
2,939
Reaction score
31
Location
Oklahoma
Ram Year
2001
Engine
5.2 V8
The only thing other than the bolts holding down the manifold is the fuel rail. Going to either have to get a fuel rail removel tool or a quick disconnect tool like shown in the pic. We used a 3/8" disconnect and it came right off.

2011-07-26_09-21-28_838.jpg
2011-07-26_09-21-47_64.jpg

Remove the bypass intake coolant hose. It's a good idea to replace that as well.
2011-07-26_10-06-52_519.jpg

Now it's time to pull the bolts from the intake. There are 12 of them, remove every single one of them and hopefully if you bought new bolts as replacements, then throw the old ones aside. Shouldn't use the old ones anyway because you won't be able to torque them down to specs.
2011-07-26_09-40-14_342.jpg

Before you pull of the manifold, pull the 4 bolts and take off the throttle body. You want to get that out of the way so it won't get screwed up. It'll look like the pic below when you do it.
2011-07-26_09-33-44_645.jpg

Now pull the intake manifold from the engine. When you do this is what you'll see.
2011-07-26_10-19-04_580.jpg

And here is the bottom side of it, the dark thing is the plenum plate. Pic below that is the inside of the plenum plate, notice the oil pooling.
2011-07-26_10-45-21_811.jpg
2011-07-26_10-57-19_212.jpg

Now you can go two ways, do what we did and pull the valve covers and replace those gaskets as well or don't. Your choice. Here's what it looks like underneath there.
2011-07-26_13-57-46_56.jpg

Take the valve covers and intake manifold outside and clean them. I used engine degreaser, dish soap, a toothbrush and water to clean them. Make sure you get as much oil out of the intake as you can.
2011-07-26_10-57-24_895.jpg
2011-07-26_14-02-04_758.jpg

Here are the new valve cover gaskets.
2011-07-26_14-07-40_730.jpg

Now time to put on the new aluminum plate and gasket. DO NOT use any gasket sealer on the plenum gasket. Use the NEW bolts that came with the kit. There are 15 of them. Use blue thread lock on them.
2011-07-26_13-13-38_106.jpg
2011-07-26_13-21-53_383.jpg
2011-07-26_13-14-20_319.jpg
2011-07-26_13-14-34_822.jpg

Now put the valve covers back on. You don't need to put any gasket sealer on it.

Here's what it looks like down the holes on the manifold. Notice the shiny aluminum :D
2011-07-26_14-30-29_128.jpg

Now put on the new manifold gaskets. Use black rtv gasket sealer where the ends meet on the gaskets.
2011-07-26_14-45-53_768.jpg

Time to put the manifold back on. Bolt the throttle body back on as well
2011-07-26_15-05-46_602.jpg

Bolt it down with the NEW bolts that came with the kit. There are 12 of these.

Then put the fuel rail back on. Be careful putting it back in.

Put the thermostat back, I, along with many others reccommend to put a 180 tstat in place of the 195. I did and it is worth the $6 to have your truck run a little cooler.

Put the accessory bracket back along with the altenator, a/c compressor and all the connectors that go with them.

Put the throttle cables back in place.

Attach all vacuum lines and connectors that are still free.

Put the radiator and fan shroud back on.

Attach all the hoses back. Refill the radiator with new coolant. Put back the coolant bottle and wiper fluid bottle on the shroud.

Put the breather back on the throttle body.

Make sure everything is back where it went and you should be good!

And here is a vid of when we first started it back up. Notice that there is no air leak. It was LOUD before and now it is smooth :naughty:
th_2011-07-26_17-42-42_502.jpg

And here mine is all put back together!
2011-07-26_17-28-11_494.jpg
2011-07-26_17-27-35_995.jpg

Anyone needing help with this or have any questions just shoot me a pm and I'll see what I can do.
 
Top