Recent content by 979dodge
-
9
What did you do with your 4th Gen this week?
got new wheels and plasti dipped all chrome. Had to make custom Ram emblems on reproductions. Up next will be black housing lights and black led taillights to complete look.- 979dodge
- Post #35,647
- Forum: General Discussions
-
9
Lowered 4th Gen Pics - Show Em Off!
Finally got some wheels. 305/35 24 sitting on 2/4 BellTech drop. -
9
What did you do with your 4th Gen this week?
Washed the 2014 and had time to plasti dip the replicas- 979dodge
- Post #34,793
- Forum: General Discussions
-
9
Lowered 4th Gen Pics - Show Em Off!
Sorry guys never post anything but I should have combined photos. 2/4 belltech done in 4hrs. Just need to replace shocks but ran out of time. Using Viking shocks in rear. Doesn’t ride bad with stocks. Plasti dipping badges and chrome with smoke soon. -
9
No brake or turn signal lights
If your truck has been lowered, you might have damaged inside of fender wells and cut into wires. Happened to me and messed up wires that run on the drivers side. Had no back lights at all. After replacing everything from bulbs, to switch under dash, I saw wires were exposed and I just used... -
9
Tire question. Pic request?
I have a 2/4 drop on my 2004 QC and i would hit on my 275/60's.(tore up both inside fender wells!) I just recently switched to 275/55's and haven't hit yet. Sorry no pics but I also like this look better than the old set up. Maybe shocks have something to do with in front? -
9
Replaced circuit board help!!!
Update! So after buying turn signal switch and taking steering wheel off to install, nothing! I come inside my house to look at Internet for more possibilities when all of a sudden I hear my truck start and my brother in law says,"I got it"! Turns out he said he cleaned and messed with harness... -
9
Replaced circuit board help!!!
I know I should have stuck with oem, but O'reilleys was first on my mind. Hate dealing with local dealership. Although even if I put my old ones back on, problem still exist. I switched one of old ones back on and same bulb is still messed up. -
9
Replaced circuit board help!!!
Might just have to try this first. Is this the tool that has the light at the top? -
9
Replaced circuit board help!!!
Hey guys! Usually don't get on here to ask for help, but I am in desperate need! It all started when my "lamp out" came on. It is a 2004 dodge ram 1500. So I found he problem and it was a bulb on drivers side. After 2 months, same message, but this time worse. After changing bulb on right side I... -
9
2/4.5 drop will i have alignment issues?
You should be fine with alignment. Only thing is that I used DJM 2" springs and I had positive camber. I had to drive it like that to shop and the whole way the tires screeched. My steering wheel was not all the way straight buy alignment guy said moog sells tie rods with more threads. Good luck!
Members online
- Mottes
- LoneStarHemi
- snoplease
- imahnu17
- 1 Ram Guy
- Mckean09
- Quick_Shifter
- Underdog493
- gunner_herman
- Jeepwalker
- Unoccupied Mass
- Racer_X
- crackerjack1957
- Joe Merchak
- AZ MARK
- jagman_xjs
- rescfrmn
- 62Blazer
- deonteglover
- Defuse
- Adamcr68
- turkeybird56
- Hardracer
- Holdin
- jmr
- myself
- rvance
- stdyrln
- FraserBoy3
- GrangerMotors
- RamDiver
- Johnboy111
- HM_SanDiego
- MrJHSN
- Warlock2024
- etbrown4
- crash
- Randy Nordstrom
- JOe G
- PA Ram
- BigTex13
- chas0472000
- Docwagon1776
- Hagar1
- Edward Taylor
- 2017EcoDiesel
- gspille
- RAM DRVR
- tomtomgt356
- Diller