-
-
GGeauxinUp replied to the thread Aftermarket stock cams any good?.I didn't miss it. Why wouldn't you get something like THIS, if you're going through the trouble of swapping the cam??
-
GGeauxinUp replied to the thread Gear ratio change.You're running a 37" tire on a big @ss truck...what mpg are you expecting?? Not likely a gear change will give you much, especially...
-
GGeauxinUp reacted to Sillygoose's post in the thread I don't fully agree with this guy,as the stock shift points are 5600 rpm,not the 6,000 he's using,but still a decent article on gearing with
Haha.
your harris bumper sticker is what's lugging that 8th gear -
GGeauxinUp replied to the thread 2025 Weird Electrical Issue with Truck waking up on door open.Yep, was gonna say those symptoms sound just like a bad battery. Glad you got it figured out
-
GGeauxinUp replied to the thread Aftermarket stock cams any good?.https://www.modernmusclextreme.com/c-298-ram-performance-camshafts.aspx https://frptuning.com/collections/hemi-magnum-cam-kit
-
GGeauxinUp replied to the thread 6.4 intake manifold paperweight?.Gonna check these out for sure. I gave up for the night…that SRV connector kicked my a$$!
-
GIf you're bored this guy has a couple decent video's on porting the 6.4 manifolds,he's doing it on the cars intake,but everything also...
-
GYou usually don't see much come out of it,but if you push a rag into it with a long screwdriver ,that'll give you an idea of how clean...
-
GStrip the manifold down as i see the map sensor is still in it,spray it full of engine degreaser then wash the hell out of the inside...
-
GGeauxinUp replied to the thread 6.4 intake manifold paperweight?.It’s used from LKQ, and it was pretty dirty. I poured some gas in there and sloshed it around best I could, then let it soak with some...
-
GYes. If there is another. I'm not very familiar with the 6.4 intake either.
-
GI'm not too familiar with the 6.4, but logical speaking, were just looking for manifold vacuum, no? So could we patch that hole and...
-
GI'm not sure. It's a judgement call. You have the part in-hand, so are in a much better position than me to decide it's probability of...
-
GIt sounds like the intake is off the truck, so it could get power washed before installation to make sure all chips are out
-
GGeauxinUp replied to the thread 6.4 intake manifold paperweight?.I think we’re gonna be good to go fellas!! Thanks for the help and ideas. Pretty sure this is gonna work perfectly
-
-
-
Loading…
-
Loading…
Staff online
-
G-Ride990Administrator
Members online
- Dodgepu360
- srv1
- Rammy16Bio
- Wild one
- caulk04
- aszumilo
- Justin33
- chopperman1
- walnuts4x4
- joe Sal
- bad_karma101
- sdstadler
- chuckster123
- Mlarv5
- Ron15
- bhayter37
- 2016 2500
- Runaround
- Stefan N
- FJ Mike
- corneileous
- jomac0321
- KansasArt
- bonnyjliss
- mboymopar
- yogibear18
- lillo123
- gjd6640
- Louiesap
- 85octane
- BenWade
- Sergio flores
- GeauxinUp
- SitKneelBend
- Ikreider
- indybp57
- RamDiver
- G-Ride990
- joshrdez91
- RidgeRunner_167
- davidthomas97
- Scott0700
- Dean2
- Skar18
- Gizmorose