Trailer Brake Disconnect - 2018 RAM 2500

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

tdoyle307

Junior Member
Joined
Oct 31, 2026
Posts
3
Reaction score
1
Location
Colorado
Ram Year
2018
Engine
Cummins
Over the last two years, I have been getting the Trailer Brake Disconnect error where the trailer brake is actually disengaged. This happens after several hours of towing (usually half way through a long trip). This comes intermittently, but typically every 15-20 minutes throughout the day - very annoying and dangerous.

I have had two technicians tell me the trailer is fine. I have replaced the seven plug and wire to the box on the trailer tougue. I have had my truck (2018 RAM 2500) at two different dealers and they do not see any issues with the tow vehicle.

Since this happens intermittently and starts after seveal days of towing (and then continues through the duration of the trip) I am wondering if this is a known issue that is not being identified by the Dodge garage.

Any thoughts on how to continue troubleshooting?
 

04fxdwgi

Senior Member
Joined
May 19, 2023
Posts
2,218
Reaction score
4,890
Location
Coastal NE North Carolina
Ram Year
2016 1500 Sport
Engine
5.7 Hemi
Have you verified the wheel / brake coil connections to the signal wire and the grounds are clean and tight?

You brake controller may be going South, but it has a higher probability of being a wiring issue.
 
OP
OP
T

tdoyle307

Junior Member
Joined
Oct 31, 2026
Posts
3
Reaction score
1
Location
Colorado
Ram Year
2018
Engine
Cummins
I actaully have not. Can you point me in the right direction to "verified the wheel / brake coil connections to the signal wire and the grounds are clean and tight"? Are you talking about checking each connection in the four wheel housings?
 

BossHogg

Senior Member
Navy Badge Law Enforcement
Joined
Feb 23, 2014
Posts
2,486
Reaction score
4,008
Location
Oakland Township, Michigan
Ram Year
2015
Engine
6.7L Cummins
Any thoughts on how to continue troubleshooting?
There are a few steps you can take to find out what the root cause is. First, throw away what you have been told. This is a random, periodic event, so for the most part, both the truck and trailer seem to be working correctly.

First, I'd want to know whether the trailer or the tow vehicle has the issue. If you have a friend who can tow your trailer, see if a disconnect happens with his tow vehicle. If you have another trailer with brakes, see if that trailer causes disconnects on your vehicle.

Connect a simulator/tester to the tow vehicle and see if disconnects happen. I personally use an Innovative Products tester for troubleshooting trailer connection issues and trailer brake connections.

Acquire and install a Tekonsha brake controller (P2 or P3 are popular) with their interface cable designed for your truck. See if the Tekonsha experiences the disconnect problem.

A brake controller sends a pulse of energy every 4 milliseconds. The brake controller senses the brake control wire for a current pull during the energy pulse. This is how modern brake controllers can tell if a trailer with brakes is connected. Any interruption to this sensing system will cause a disconnect. This is what it looks like on a scope;
1793617820991.png

Tell us more about your trailer. Are the brakes electromagnetic or electric-over-hydraulic? How many trailer axles have brakes? What settings are selected on the brake controller?

Do the disconnects happen while braking or cruising along? If they happen while braking, is it an aggressive stop that triggers the disconnect?

Typically, trailer brake issues are a grounding issue. While ohming out the connections looks good, the problem with iffy connections is current flow. Trailer brakes, electromagnetic, for example, will pull about 4 amps of power when stopping. Multiply that number by two or four, and all of a sudden you have 16 amps of power being used for the brakes. An iffy connection will cause problems when trying to flow that much current.
 
Last edited:

04fxdwgi

Senior Member
Joined
May 19, 2023
Posts
2,218
Reaction score
4,890
Location
Coastal NE North Carolina
Ram Year
2016 1500 Sport
Engine
5.7 Hemi
There are a few steps you can take to find out what the root cause is. First, throw away what you have been told. This is a random, periodic event, so for the most part, both the truck and trailer seem to be working correctly.

First, I'd want to know whether the trailer or the tow vehicle has the issue. If you have a friend who can tow your trailer, see if a disconnect happens with his tow vehicle. If you have another trailer with brakes, see if that trailer causes disconnects on your vehicle.

Connect a simulator/tester to the tow vehicle and see if disconnects happen. I personally use an Innovative Products tester for troubleshooting trailer connection issues and trailer brake connections.

Acquire and install a Tekonsha brake controller (P2 or P3 are popular) with their interface cable designed for your truck. See if the Tekonsha experiences the disconnect problem.

A brake controller sends a pulse of energy every 4 milliseconds. The brake controller senses the brake control wire for a current pull during the energy pulse. This is how modern brake controllers can tell if a trailer with brakes is connected. Any interruption to this sensing system will cause a disconnect. This is what it looks like on a scope;


Tell us more about your trailer. Are the brakes electromagnetic or electric-over-hydraulic? How many trailer axles have brakes? What settings are selected on the brake controller?

Do the disconnects happen while braking or cruising along? If they happen while braking, is it an aggressive stop that triggers the disconnect?

Typically, trailer brake issues are a grounding issue. While ohming out the connections looks good, the problem with iffy connections is current flow. Trailer brakes, electromagnetic, for example, will pull about 4 amps of power when stopping. Multiply that number by two or four, and all of a sudden you have 16 amps of power being used for the brakes. An iffy connection will cause problems when trying to flow that much current.
A lot of info there, but "throw out what you have been told"? I suggested he check the wiring.
That should be the very 1st thing to check....
 

BossHogg

Senior Member
Navy Badge Law Enforcement
Joined
Feb 23, 2014
Posts
2,486
Reaction score
4,008
Location
Oakland Township, Michigan
Ram Year
2015
Engine
6.7L Cummins
A lot of info there, but "throw out what you have been told"? I suggested he check the wiring.
That should be the very 1st thing to check....
My thought, based on what the OP told us, is that the trailer brakes work, but sometimes he sees a disconnected message. It seems the wires are connected. What would you check with the wiring? As I said, it could be a wire connection failure during a high-current flow condition. I hope the OP comes back with additional information.
 

04fxdwgi

Senior Member
Joined
May 19, 2023
Posts
2,218
Reaction score
4,890
Location
Coastal NE North Carolina
Ram Year
2016 1500 Sport
Engine
5.7 Hemi
My thought, based on what the OP told us, is that the trailer brakes work, but sometimes he sees a disconnected message. It seems the wires are connected. What would you check with the wiring? As I said, it could be a wire connection failure during a high-current flow condition. I hope the OP comes back with additional information.
Although the wiring "seems the wires are connected", that is less than a comforting indication that all is good. An intermittent fault would give fake positives as well as negatives.

I would 1st focus on the wheel magnet wiring to see if any wiring was chaffed or damaged, then check the ground connections to be clean and tight, since that is where the controller gets the signal that the trailer is connected. If just one magnet connection is bad, then the whole thing fluctuates and throws off the controller. Some controllers may be more sensitive to the fluctuations than other controllers.

One good test would to be disconnect the controller and put a tekonshka in to see if it behaves or not. That would isolate a problem trailer or wiring vs: a problem controller.

Just my opinion, of course.
 
Last edited:
OP
OP
T

tdoyle307

Junior Member
Joined
Oct 31, 2026
Posts
3
Reaction score
1
Location
Colorado
Ram Year
2018
Engine
Cummins
Thank you for your advice. I will proceed in the troubleshooting with this additional detail.
 

Members online

Forum statistics

Threads
213,354
Posts
3,092,143
Members
174,575
Latest member
DITRIO
Back
Top