Search results

  1. Josh88

    Angles

    Your not the only one
  2. Josh88

    Gas mileage for those with 37s

    2014 1500 5.7 hemi, 3.21 gears, 6in with a 3in body, running on 37 x 12.5, I'm getting 16mpg I also shut off the Mds hope that helps
  3. Josh88

    Gas mileage for those with 37s

    2014 1500 5.7 hemi, 3.21 gears, 6in with a 3in body, running on 37 x 12.5, I'm getting 16mpg I also shut off the Mds hope that helps
  4. Josh88

    37’s too big for 2014 ram 1500 5.7 Hemi big horn?

    ok makes sense now, lol yeah I'm heading in that direction of a 4th gen 2500 turbo some day, thanks though
  5. Josh88

    37’s too big for 2014 ram 1500 5.7 Hemi big horn?

    Did you regear I was debating on 40s one I got the lift
  6. Josh88

    Angles

    id have to agree, I had almost the same setup with the 3inch spacer and one in the back, with the 3inch body, I decided to bite the bullet and put the 6in suspension in, and OMG amazing I didn't realizes that my truck rode like a brick until I did it, it rides better then stock now and couldn't...
  7. Josh88

    37’s too big for 2014 ram 1500 5.7 Hemi big horn?

    I have about 2inch of poke my tiers are 12.5
  8. Josh88

    37’s too big for 2014 ram 1500 5.7 Hemi big horn?

    I agree go for it you will be pleased I am,
  9. Josh88

    My Build So Far

    Yeah I'm definitely pleased with it I wouldn't mind gaining probably another 2in some how, there is a fine line of looking good and just odd being to high above the tiers
  10. Josh88

    My Build So Far

    Good to know rear 47.25 front 47.5 same on other side, hope that helps
  11. Josh88

    My Build So Far

    Thanks guys measurement is front 31" from center of hub roughly to fender and rear is 30 1/2" 3inch rear
  12. Josh88

    My Build So Far

    Honestly it wasn't hard just sucked I guess, the hardest part was the bumper bracket
  13. Josh88

    My Build So Far

    Alright so I finished up my Zone 6in lift today and thought is post the progression of my build since I purchased the truck last October, this is stock then I went with a motofab 3" level and 1.5 in rear next came the 3" PA body lift with some 18 x 9.5 wheels and a old set of 35 x 12.5 tiers...
  14. Josh88

    Zone 6inch preload spacer

    Awesome thanks
  15. Josh88

    Zone 6inch preload spacer

    Alright just about done last question which hole these the track bar go on I've seen one or the other used?
  16. Josh88

    3" pa body lift pics

    Lol yes they are 12.5x35 r 18 it got me the look I wanted but it wasn't enough I'm actually just finishing up my zone 6in and getting 37s on Monday I think I'll be satisfied with that hopefully lol
  17. Josh88

    Zone 6inch preload spacer

    Thanks guys front is done! Working on the rear
  18. Josh88

    Zone 6inch preload spacer

    Cool so I flipped that around still seem close to the CV is that normal? Thanks for the help it's kinda odd if that's normal because if you wanted to replace that camber bolt you would have to remove that cv
  19. Josh88

    Zone 6inch preload spacer

    @Quick_Shifter So have you ran into this problem my rear crossmember banner bolt it's my CV the front differential is lowered and seem to be in the right spot
  20. Josh88

    Zone 6in lift tips

    Ah no I was getting parts ready for install I am replacing the factory struts and upper control arms, I will be digging into it tomorrow, its been killing me seeing the lift and 37's sitting around for awhile but finally have some nice weather in NH
  21. Josh88

    Zone 6in lift tips

    3in coils in the rear I don't remember the measurements but that should leave it out
  22. Josh88

    3" pa body lift pics

    I have a 3inch pa with a 3in level in front, 1.75 in rear
  23. Josh88

    Zone 6in lift tips

    Hey guys I am installing my zone 6inch lift this weekend, any tips or tricks would be great Thanks
  24. Josh88

    Zone 6inch preload spacer

    Awesome thanks, this saves me from taking the strut apart for the fourth time, thanks for the help
  25. Josh88

    Zone 6inch preload spacer

    so I have both of the spacer in one strut is completely flat and the one on the left at a slight angle, it seem to straiten out when I compress one side of the spring, this still seems normal? I have a little OCD and cant stand that its like that, do you think it will straiten out one installed?

Latest posts

Staff online

Members online

Total: 1,301 (members: 46, guests: 1,255)
Robots: 1,809

Forum statistics

Threads
195,684
Posts
2,873,293
Members
156,551
Latest member
hemi57driver

Share this page

Top