Recent content by vinstang67

  1. V

    My Running board lighting mod, bed lighting mod and other lighting mods :)

    Yep, it's dark under the bed cover (I have a white truck but got a bedrug). Trying to decide battery operated stand-alone or wired. Before anything, I got too much projects to finish (around the house & garage). I guess every blackbetty got bad ass vehicles:)
  2. V

    HID Retrofits: Non-Morimoto Ballasts Inside Stock Headlight Housing?

    Tight squeeze indeed. It took me a while to get everything fit in mine.
  3. V

    My Running board lighting mod, bed lighting mod and other lighting mods :)

    Looking good! Look forward to the bed lighting. BTW, Are you the blackbetty used to have gen3 and lived in middle TN that I know of?
  4. V

    How many guys have CCLB Sports?

    Here's mine:) I wanted CC w/ 6.4 bed. There have been a few times that I was glad with 6.4 bed though quite a bit of difference compare to my old truck (04 QC).
  5. V

    Cell Phone Mount in 1500

    I've used Proclip mount on 4 other vehicles, and this is the 5th one (that I rigged a little). I am not favoring it blocking (not entirely though) the vent & a little floppy by the way I set it up so I am thinking about rigging something else now.
  6. V

    2013+ HID headlights kit follow up

    You are correct, and passed the test:) I had it switched around, and needed to flip. I did not take any pics after that. I was hoping none would notice........
  7. V

    2013+ HID headlights kit follow up

    The driver side was a different story. I had to shave a port of the retainer ring. 1st pic shows the ring removed. 2nd is how the ring was shaved off where the ballast hits against. 3rd is how everything is inside. I managed to break the lower bottom push pin (passenger side) when I took the...
  8. V

    2013+ HID headlights kit follow up

    2013+ HID headlights kit done I got the kit from Jeremy last month and I am very happy with it. I just wanted to post some pics here hopefully would help others considering the kit. 2013+ HID (for factory projector) 35W kit: 2 x HID 35W bulbs 2 x 50W ballasts (he was out of 35W) 2 x...
  9. V

    13+ Headlight Harness and HID kit installed, have concerns..

    The female of the plug is not exactly ring on the center so I adjusted the pin slightly when I did mine. If the kit is working, I wouldn't worry about it. As for the light patterns, I am guessing the passenger side is what you have a shadow (of the brown piece). The bulb goes in one way...
  10. V

    Has anyone install the new ballast from retroshop into projectors

    I was very close to say f-it....lol.
  11. V

    Has anyone install the new ballast from retroshop into projectors

    I have the kit contains: 2 x HID 35W bulbs 2 x 50W ballasts 2 x AMP connectors 2 x canbus adoptors I was able to put them all in but I removed the bulb retaining ring, put all in, then reinstalled the ring. I still have to so the driver side. So far, I managed to break the passenger...
  12. V

    Has anyone install the new ballast from retroshop into projectors

    Thanks for the tip. I will take time & play by the ears.
  13. V

    Has anyone install the new ballast from retroshop into projectors

    Thank you for posting the pic. I am just about to do the same.
  14. V

    Question on 13+ headlight kit

    Jeremy just cleared everything for me through email, and OK to run 35W kit with 50W ballasts. Instead back ordering mine (he was out of 35W ballasts), he shipped with 50W ballasts. I ordered yesterday morning, and I got the kit today. Super Fast shipment!!!
  15. V

    Question on 13+ headlight kit

    Thanks. Good to know there is nothing burns my arm on this kit. I am not sure if they use or design 50W ballasts for all (35W & 50W) HID kit or OK to use 50W ballasts for 35W kit. My brain is not trained for electrical work and I have no idea how those thing work. I hope Jeremy will...
Top