Lifted 4th Gen Pics - Show Em Off!

[olyelr]

No I'm using them for lift, just to level the truck when towing. But its lifted now and some say I will need spacers because it's lifted

Hmmm, well, most lifted trucks end up sitting level when unloaded. So yea, if your truck is level and then you load it up, if very well could become low in the back.

Spacers would fix this issue when loaded, but will cause it to be high in the back when unloaded.

That is where air bags shine. The truck can be leveled when empty AND loaded.

 

[Jd1990]

4" Ready Lift sst with 17" Fuel D531 and 35" BFG KM3s

 

[Graygoose]

@Jd1990 great combo, love that color!

 

[co-pilot]

Looks good!!!...nice stance......And I kinda like that color too!!

 

[RRF1992]

A little bit more rake than I wanted but still looks good.

 

[JB1]

A little bit more rake than I wanted but still looks good. View attachment 158903 View attachment 158904

Looks great, what’s the specs on the lift

 

[bigred74]

And what was your rake before and after lift?

 

[Graygoose]

@RRF1992 looks great!

 

[RRF1992]

Thanks. I got a 6 inch BDS lift on it. 35x13.5 Ridge Grapplers and 20x10 Gear Alloy Big Blocks. Still has about 2 inches of rake. Currently exploring options to lift up the front a bit.

 

[BTD07]

Thanks. I got a 6 inch BDS lift on it. 35x13.5 Ridge Grapplers and 20x10 Gear Alloy Big Blocks. Still has about 2 inches of rake. Currently exploring options to lift up the front a bit.

Do you have the Bilstein 5100s up front? Would pretty much solve that

 

[RRF1992]

That's actually what I'm thinking about doing. Just wanted to make sure it wont mess up the geometry too much, adding that to the lift.

 

[JB1]

Thanks. I got a 6 inch BDS lift on it. 35x13.5 Ridge Grapplers and 20x10 Gear Alloy Big Blocks. Still has about 2 inches of rake. Currently exploring options to lift up the front a bit.

you must have the 5" rear coils

 

[RRF1992]

you must have the 5" rear coils

That I do. The installer did not ask me which set of coils I wanted me and told me that it would be pretty much level with the 5".

 

[bigred74]

That I do. The installer did not ask me which set of coils I wanted me and told me that it would be pretty much level with the 5".

Nope, 3" levels it and 5" keeps rake. Can make them swap out for a 3in or add bils upfront depending how tall you want your truck to sit. If you add bils you will most likely want 37" tires

 

[co-pilot]

Thanks. I got a 6 inch BDS lift on it. 35x13.5 Ridge Grapplers and 20x10 Gear Alloy Big Blocks. Still has about 2 inches of rake. Currently exploring options to lift up the front a bit.

I really like those Gear Alloys!!......I almost went with those.......The 13.5s are really wide!!!......truck looks great!

 

[dkcon05]

Just got the Ram lifted! Had it since last Mother’s Day.

2012 big horn, 6” RCX with front kickers. 1.25” wheel spacers on 35x12.5R20 Toyo R/Ts

Shop didn’t drop bils down from 2.8 or take off 1.5” rear spacers. Love the height and stance, just too tall for my 35’s

Dropping in back off to have spacers removed and bils adjusted. Any suggestions on front settings?

Also anyone have issues with steering sensors.



Sent from my iPad using Tapatalk

 

[dkcon05]

Sent from my iPad using Tapatalk

 

[BTD07]

Just got the Ram lifted! Had it since last Mother’s Day.

2012 big horn, 6” RCX with front kickers. 1.25” wheel spacers on 35x12.5R20 Toyo R/Ts

Shop didn’t drop bils down from 2.8 or take off 1.5” rear spacers. Love the height and stance, just too tall for my 35’s

Dropping in back off to have spacers removed and bils adjusted. Any suggestions on front settings?

Also anyone have issues with steering sensors.



Sent from my iPad using Tapatalk

Take the spacer out, drop the bils to .7. Should be pretty level then

 

[8732cuts]

Having fun in the Sand

Sent from my SM-N960U using Tapatalk

 

[JB1]

Having fun in the Sand

Sent from my SM-N960U using Tapatalk

Nice......San Luis pass?