New 22x10 hellcat shoes and painted calipers
- Thread starter blackbetty14
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
OP
OP
blackbetty14
Senior Member
- Joined
- Oct 23, 2014
- Posts
- 2,701
- Reaction score
- 1,426
- Location
- CT
- Ram Year
- 2024
- Engine
- Hemi 5.7 VVT/Etorque
Thank you guys! Lovin it. Havent driven her except 1 day lol... been taking the 700hp supercharged hot rod to work the last few days 
OP
OP
blackbetty14
Senior Member
- Joined
- Oct 23, 2014
- Posts
- 2,701
- Reaction score
- 1,426
- Location
- CT
- Ram Year
- 2024
- Engine
- Hemi 5.7 VVT/Etorque
Your going to have to make them. lol.
I run a dynomax 409SS catback. muffler back is 2.5" not stock 2.25" so I used 2.5" to 4" tips and cut them, then welded on some 4" in 5" out double walled slanted SS tips
Allows me to tilt them closer to the bumper to lessen the gap between the tip and bumper.
KCaudill
The RAM
- Joined
- Mar 10, 2016
- Posts
- 434
- Reaction score
- 135
- Location
- Blacksburg, Va
- Ram Year
- 2016
- Engine
- Hemi 5.7
wow very nice, Where did you get them? You said you have to do what to the calipers to fit?? Please explain a little more please
OP
OP
blackbetty14
Senior Member
- Joined
- Oct 23, 2014
- Posts
- 2,701
- Reaction score
- 1,426
- Location
- CT
- Ram Year
- 2024
- Engine
- Hemi 5.7 VVT/Etorque
Got them from OEwheel. Didn't have to do anything to the calipers. I removed them to paint them. Only thing u have to remove is the star retaining clips that the factory puts on the wheel studs to hold the rotors on. Some small pliers will remove them otherwise the wheel doesn't fit flat against the rotor.
cdsbj6508
Junior Member
- Joined
- May 10, 2017
- Posts
- 24
- Reaction score
- 15
- Ram Year
- 2017
- Engine
- 5.7 Hemi
Your going to have to make them. lol.
I run a dynomax 409SS catback. muffler back is 2.5" not stock 2.25" so I used 2.5" to 4" tips and cut them, then welded on some 4" in 5" out double walled slanted SS tips
Can I do this with the stock exhaust with a muffler delete?
Sent from my iPad using Tapatalk
OP
OP
blackbetty14
Senior Member
- Joined
- Oct 23, 2014
- Posts
- 2,701
- Reaction score
- 1,426
- Location
- CT
- Ram Year
- 2024
- Engine
- Hemi 5.7 VVT/Etorque
Sure. Stock tips use a ball flange and most likely you will have to cut the stock tips off before the ball flange on the muffler side like 12-14" back from the tip. Basically right behind he ball flange to get rid of it. Then get some cheap 2.25" to 4" exhaust adapters (you might need to go 2.25 to 3 and then 3 to 4" as they only come in certain sizes. Then just weld the 4" inlet and 5" outlet tips onto the adapter you just made. Slip the new tip over your cut exhaust and use a SS band clamp and your done.
Got the tips off eBay for like $40 each.
