What did you do to/with your second gen today?

[dodge dude94]

One guy I know he has a 99 dodge 2500 short bed. His bed was beat to ****. So he put a 70s stepside bed on it and used a new jeep wrangler front bumper as his rear. Not my taste but it's pretty neat imo.

Sent from my SM-G900V using Tapatalk

Well wtf now.

 

[jbmobbs]

Well wtf now.

Everybody will definitely know it's him Rollin around lmao

Sent from my SM-G900V using Tapatalk

 

[clownprince]

I'm not completely crazy about that bed but looks good and is unique for sure!

 

[joepizuro]

Noticed my 4wd wouldn't engage. I have a cable actuator by posilok or something.. so I took it apart and ended up finding the cable was melted to itself by the new headers a shop put in. Sooooo now I'll try to get a hold of the people that make these before winter comes. Lol

 

[codered]

Noticed my 4wd wouldn't engage. I have a cable actuator by posilok or something.. so I took it apart and ended up finding the cable was melted to itself by the new headers a shop put in. Sooooo now I'll try to get a hold of the people that make these before winter comes. Lol

Damn man!


Sent from my iPhone using Tapatalk

 

[DodgeTx]

Got my 3inch coil spacer installed with my dads help Sunday Morning. Also got the 315/70/17s mounted! My dad also gave me one of his old 16 inch 315/70/16 so I could mount on my spare. Got a few pics, my buddy at discount tire installing the tires for me on the cheap

I have some slight rub on turns, but it is awesome!!! Need to lift the rear but my rear lift kit was only 2.5inch wide they sent the wrong kit and now say the don't make a 3inch wide kit even though I purchased one.

Yes this is on the truck I revived from the dead after mudding and epicly failing almost ruining my tranny.

 

[BlackMagnum2000]

Still on jack stands, been super busy. About to start control arm bushings and hopefully finish up my rear end today. Transfer case is done just need to find a way to get the fill plug out (PO stripped it) so I can change the fluid. Then to start finally regearing my front end, fix my exhaust somewhat, and get some tires and get it aligned

 

[BlackMagnum2000]

Wish I had the money, I'd be buying new springs, long arms, and new shocks.

 

[jbmobbs]

Wish I had the money, I'd be buying new springs, long arms, and new shocks.

Same here lmao

Sent from my SM-G900V using Tapatalk

 

[jsmith]

Still on jack stands, been super busy. About to start control arm bushings and hopefully finish up my rear end today. Transfer case is done just need to find a way to get the fill plug out (PO stripped it) so I can change the fluid. Then to start finally regearing my front end, fix my exhaust somewhat, and get some tires and get it aligned

I just got done dealing with the same pain in the ass stripped fill plug. I ended up chiseling a groove in it and then used an air hammer set in new groove to spin it free. NAPA has nice replacement plugs part# 7041048

 

[dapepper9]

I should change my tcase fluid before winter....pretty sure it's the same fluid it rolled out the factory with

 

[dodge dude94]

You should do that. I need to check my axle again.
****ttttt

 

[joepizuro]

Still on jack stands, been super busy. About to start control arm bushings and hopefully finish up my rear end today. Transfer case is done just need to find a way to get the fill plug out (PO stripped it) so I can change the fluid. Then to start finally regearing my front end, fix my exhaust somewhat, and get some tires and get it aligned

Put a pair of vice grips on it. Worked for me

 

[joepizuro]

Posilok quoted $90 for a new wire and $12 for shipping... expensive bad routing..

 

[BlackMagnum2000]

I just got done dealing with the same pain in the ass stripped fill plug. I ended up chiseling a groove in it and then used an air hammer set in new groove to spin it free. NAPA has nice replacement plugs part# 7041048

Thanks for that PN

I should change my tcase fluid before winter....pretty sure it's the same fluid it rolled out the factory with

Yeah.. I'd do that. Lol

Put a pair of vice grips on it. Worked for me

Well mine is an Allen key plug otherwise I'd do exactly that. I'm thinking of trying to hammer a Torx into it. Just anything to keep from drilling into it to get metal in there

 

[joepizuro]

Thanks for that PN

Yeah.. I'd do that. Lol

Well mine is an Allen key plug otherwise I'd do exactly that. I'm thinking of trying to hammer a Torx into it. Just anything to keep from drilling into it to get metal in there

Mine took the ratchet with an extension but it stuck out 1/4 inch thankfully. Was stripped to ****

 

[bagged 01 1500]

Installed 2 12's an a kicker amp now my truck has 10 speakers

 

[BeauDuke01]

One guy I know he has a 99 dodge 2500 short bed. His bed was beat to ****. So he put a 70s stepside bed on it and used a new jeep wrangler front bumper as his rear. Not my taste but it's pretty neat imo.

Sent from my SM-G900V using Tapatalk

i actually really like that.

 

[NightMares]

I ordered more parts for the truck today!



...


....

to replace the wrong part they sold me so I can actually DRIVE my truck.

******* idler pulley.

 

[DodgeTx]

new lift blocks for the rear supposed to come in Saturday we'll see. and we'll also see if they send correct ubolts.