Recent content by 1970Pelle

  1. 1970Pelle

    Film on inside of windshield

    Its from the plastic parts inside your vehicle. It emits a vapor that lands on the inside glass. The way to clean your inside glass is alcohol. Just your everyday liquid alcohol you pick up at the drug store or Walmart. Even alcohol wipes work great. Thats what I use, take a couple at a...
  2. 1970Pelle

    More money than brains

    I hate the fact that they distroy trucks & cars I would love to have. But are out of my range of even thinking about owning. One of these days there luck is going to run out. There going to hurt themselfs or even worse hurt or kill an innocent bystander. I read about the fines, these type...
  3. 1970Pelle

    Trailer brake module failure?

    The issue I think your having is the truck factory wiring and smart instrument cluster. When you installed the trailer brake controller, you used the supplied harness. This harness wires up to your provided controller, and then plugs into the trucks wiring harness. Correct? Now I'm not...
  4. 1970Pelle

    Trailer brake module failure?

    You are using the factory electric brake wiring? It has a blue wire for the electric brakes correct? And you have it hooked up to the add on brake controller? If you have answered yes. To any of the questions. Pull the cluster and look for a burnt CKT.
  5. 1970Pelle

    Is anyone's oil NOT black immediately after an oil change?

    Its a by product of combustion. Your new engine oil is still brand new. The only issue is they dye in the oil has changed to black. From the above statement. You wanted a Cummings, here is a slight negative if you like. But it doesn't effect the function of your engine oil A diesel engine is...
  6. 1970Pelle

    Going old school on a 1987 B350. I have questions

    You won't have any trouble at all. I have a 1990 that has been changed from TBI system to a edelbrock intake manifold with a edelbrock 4 bbl carb. It has no EGR valve anymore, and the host of vaccum lines has ended. I'm still using the in tank electric fuel pump. I just use a fuel pressure...
  7. 1970Pelle

    OK QUESTION for any one whose builta DODGE RAT ROD. Please read at least my 1st post .

    I apologize I haven't been following your build very close. The only thing stopping that trans upgrade is you. Go for it, you just need to researh the swap. The find the correct parts needed. And with the frame clear of sheet metal the swapping of parts will be much easier. A bunch of folks...
  8. 1970Pelle

    Trans Fluid

    ATF Plus 4. I remember when this change was implemented by Mopar. Everyone balked at the idea of just one ATF. And mixing ATF, after years of being told never mix your fluids. But after seeing and using for years. Its the way to go. I have never heard or seen anything but good by making the...
  9. 1970Pelle

    Anyone Installed one of these?

    When I had my 1985 C10 Chevy, I bought a 3 gauge a-pillor pod. Here is a tip to make them look just like stock moldings and trim. Litely sand the pod. Lite coat of primer. Now this is the trick part. Buy a spray can of Duplicolor bedliner. This stuff works great, it comes in a gray and black...
  10. 1970Pelle

    where to get parts

    Ramcharger and pickup dash parts are the same. I double checked my FPM and my FSM part numbers the same. Dash stuff is plentyfull here in N.E. Florida, check the LQK websites. They will send alerts when one hits the yard. That's how Have found my parts needed. And I bought a parts truck. I...
  11. 1970Pelle

    1986 D-150 A/C issue.....

    I have complete replaced every part of my W150's A/C system. I have bought 80% of my parts from RockAuto. DW150 and DW350 parts are the same in most instances. I did go with a Sanden A/C compressor, made my own brackets. I use a sanden scroll compressor. And I buy my parts for 134A system...
  12. 1970Pelle

    Won't start on gas

    Lift the bed, don't drop the tanks. With the bed off everything is right there, held in place easy to clean out. Use a cherry picker to lift the bed. Or do one side at a time.
  13. 1970Pelle

    OK QUESTION for any one whose builta DODGE RAT ROD. Please read at least my 1st post .

    I think your making more work for yourself by cutting the body away and leaving the lower parts. The biggest differance your going to find is the older truck is much narrower that the donor truck. A plasma cutter is the tool for getting everything apart. I think it would be much easier to...
  14. 1970Pelle

    Frozen screw jack on my 87 D150 any ideas how to get it unstuck ? Tried penetrating oil and tapping with a hammer no good. I can drill out rivets but

    I have a pretty decent one you may have. Cover shipping from Florida
  15. 1970Pelle

    Lost the crank bolt ~~

    I have a few, send me a PM with your mailing addy and I'll get one headed your way. Ken
See more

Latest posts

Members online

... and 1 more.
Total: 1,296 (members: 51, guests: 1,245)
Robots: 1,846

Forum statistics

Threads
195,633
Posts
2,872,778
Members
156,464
Latest member
RayMorrow44

Share this page

Top