Recent content by 1qikdsl
-
Strictly the 4x4 lowering thread...
I had the exact same truck. I ran the groundforce 2/4 kit. Aligned within spec. handled great! Had a nice stance to it. Install took me 2.5 hours. If its your first time and you don't have access to an impact I would plan 4 or less safely. I used factory shocks and had no issues and feel... -
Lowered 4th Gen Pics - Show Em Off!
Are you still running factory bumps in the rear? If so I would either trim them a little shorter or run a shorter aftermarket bump stop. I wouldn't recommend removing them all together. Hitting bump stop is annoying but hitting metal to metal would be much worse -
Strictly the 4x4 lowering thread...
This isn't uncommon. Mine did this with stock as well as lowered. My OCD got the best of me and I pulled out a cutoff wheel. I don't recall if it was a half or full coil removed since it was done to both my stock and lowering springs. It's a quick job and he spring still stays tight in the... -
Strictly the 4x4 lowering thread...
They will fit. Stock tires and wheels fit without any issue. I had 22x10 srt 10 whees on mine with a 305x45r22 nitto tire. Zero modification or rubbing. You would be good to go -
Strictly the 4x4 lowering thread...
I cut 2 coils of each. Not sure when wag begins I no its been a bigger issue with 2wd. I only ran belltech trac bar relocation bracket and short seat bar endlinks. My truck did t sit low enough to need anything else and my rear wheels and tires didn't have the sucked forward look so I didn't... -
Strictly the 4x4 lowering thread...
I also agree with mcgaughy 2 inch rear level springs. I went this route initially. Then bought ground force front springs and cut the rear mcgaughy springs a coil at atoms until I achieved the look I was after. I also used shorter bell tech sway bar end links and a belltech rear trackbar... -
Lowered 4th Gen Pics - Show Em Off!
If it's a belltech kit the coils will be Grey in color. If so check that your rear track bar is tight and inspect the track bar relocation bracket for cracks. I know two people who have had the relocation bracket crack and it made the truck for obvious reasons squirrelly and sketchy to say the... -
-
Strictly the 4x4 lowering thread...
Something isn't correct. Shouldn't matter what spring is on what side. Mine always sat perfectly level. The isolator isn't binding up on either side correct? -
Strictly the 4x4 lowering thread...
Thank you very much! I really liked how it looked and hamdled but with all the pot holes it started to get old plus every time it rains the roads flood and I can't see the holes and mud lol. I started hunting and camping more with my boys and want to be able to let them steer like I did growing... -
-
Strictly the 4x4 lowering thread...
I'm not sure why but can someone tell me why I'm not able to post in classifieds? I tried to post my 4x4 drop kit and it won't let me. Maybe it's not like the diesel forum I use to frequent and I have to pay or something? I prefer a local sale obviously but I thought if it was posted here I may... -
Another tire ?
I know I have to align it After any front end change. I was curious if when they align it in the 2.8 setting if the camber can be adjusted flat again or if the bottom of the tire is pulled in a little -
Another tire ?
Thank you. I am aware of the uca's. Still trying to decide what route I want to go as far as uniball or save the money lol. -
Another tire ?
If you go 2.8 does front end still meet specs or does it pull the bottom of the tire in and wear the outer edge?
Staff online
-
rule18Admin
Members online
- jawzs2
- bcraig
- crackerjack1957
- Slinge
- Dbow20
- Tri-J
- dalcini
- TC
- Dontra
- mtofell
- jabartram
- Woodsrunner28
- Prorider17
- CanuckRam1313
- hemihustlin
- PaleFlyer
- duunoit
- Rufi
- AZ MARK
- PJs97Talon
- northlane1
- randygrove
- Dark Knight G45
- JimJam300
- Daw14
- Luisp22
- tidefan1967
- saturnx
- Zach2000
- 1998RamMan
- nwflsr4x4
- skuppy069
- abates362
- seems fishy
- PA Ram
- 3TV
- bob49
- Baja1
- Pears
- Curmudgeon
- Mfalty24
- rule18
- 18CrewDually
- Maniac
- CRS1968
- audiophile
- BDay2351
- jws123
- Demon13
- zstroken