Recent content by AEDELGOD
-
8hp70 heater bypass
@caulk04 thanks for bringing this to my attention. I will take a look at it later tonight. For the record though I am not set up to ship outside of the U.S. currently but looking into it. For now, any orders to Canada can be fulfilled by @caulk04 directly and will let him know when I can start...- AEDELGOD
- Post #679
- Forum: Engine & Performance
-
Bottom End Knock.
If rods and bearings look good, and the top end looks good, the only thing I can think of is a piston ring or wrist pin coming loose. Those would usually show obvious scoring in the cylinder walls. How do your cam bearings look?- AEDELGOD
- Post #2
- Forum: Engine & Performance
-
Peculiar findings doing my MDS delete and would like everyone's thoughts.
Hey all, So I am in the middle of doing a top-end rebuild with an MDS delete and doing the HC oil pump. Throughout the disassembly process I kept noticing marker marks and numbers, is this something the factory does? I am getting the feeling someone has been in here before or someone put a...- AEDELGOD
- Thread
- Replies: 3
- Forum: Engine & Performance
-
Issues with AlfaOBD and changing tire size
Preliminary, it appears to be a read/display bug with the app not giving the correct/current value. I've reported my findings to Alexey just now. I was able to correct my friends truck but I had to put my programmer hat on and really critically think through how the software code is likely...- AEDELGOD
- Post #18
- Forum: 4th Gen DIY
-
Issues with AlfaOBD and changing tire size
ABS initialization is greyed out for us. He has a 2015 Sport and I have a 2014 Lone Star. Doesn't let us select start on that menu. It's definitely taking our changes though. The issue that is racking my brain is I've never done this procedure before on my own truck and I have stock 20" wheels...- AEDELGOD
- Post #15
- Forum: 4th Gen DIY
-
Issues with AlfaOBD and changing tire size
So I've only done the tire change procedure to it. Went into BCM and ran that procedure, disconnected, cycled key off waited a minute, turned it back to run. Then connected into ABS and did ECU initialization, cleared CELs, disconnected, cycled off and back to run, then did clearing rolls...- AEDELGOD
- Post #10
- Forum: 4th Gen DIY
-
Issues with AlfaOBD and changing tire size
Yes, it went into limp mode, locked up the electronic steering and had multiple codes for implausible data. AlfaOBD app says max possible value is the one it is set at now (same with my truck but never messed with mine like that - still have 20" sports on mine and original tire size, again...- AEDELGOD
- Post #7
- Forum: 4th Gen DIY
-
Issues with AlfaOBD and changing tire size
What's throwing me off is mine and his truck used to say 2750mm but now says 65535mm (max value) and each normal value I put on my friend's truck puts it into limp mode but when I put the max value on his it became drivable again but off by 4 (slow) when it was originally only off by 1. I still...- AEDELGOD
- Post #4
- Forum: 4th Gen DIY
-
Issues with AlfaOBD and changing tire size
Hey everyone, Wondering if anyone else is running into this issue. I went to change the tire size on my buddy's 2015 Sport and followed everything to the T, looked up his tire size and all to get the correct mm size, etc. To keep a long story short, after many attempts at it I went an pulled my...- AEDELGOD
- Thread
- Replies: 24
- Forum: 4th Gen DIY
-
2014 Ram 4x4 Transfer Case shaft to Driver side CV question
Thanks Wild One. Tie rods have been replaced and everything else looks good and snug but I might need to take it somewhere to have everything measured as something just might be slightly bent (or tire feathering might be throwing it off now). Truck has never been lifted and is all stock. My main...- AEDELGOD
- Post #9
- Forum: General Discussions
-
2014 Ram 4x4 Transfer Case shaft to Driver side CV question
Hey Jeepwalker, Thanks for your patience and for reaching out, I made a video showing everything. There's really no up-and-down play with it, just a little side-to-side. https://photos.app.goo.gl/Ss3XEskBkHXP17oL9 The truck has 122,000 miles. The CV Axle in question doesn't look original but...- AEDELGOD
- Post #7
- Forum: General Discussions
-
2014 Ram 4x4 Transfer Case shaft to Driver side CV question
Hey everyone, Hoping someone might be able to point me in the right direction. This is my first Ram and first 4x4 truck so I've never owned or worked with a design like this before. I just got my new to me 2014 Ram 1500 4x4 with 5.7 Hemi and I noticed this with the driver-side CV axel to the...- AEDELGOD
- Thread
- Replies: 8
- Forum: General Discussions
