Recent content by Tfrizz80
-
2015 ecodiesel build....
Actually I forgot to get that done thanks for reminding me. when u put them in they have a lot of pressure on them but I will get them welded when I get my exhaust finished up. All you have to do it get a good tach on it so they don't vibrate out. There is a plastic pad on the frame where u need... -
-
2015 ecodiesel build....
My ride is the same if not better with 5100s at 2.8. I got the gap guards and highly recommend them for the front wheel wells. I don't like the gap and don't want dirt and junk getting in my engine compartment. As far as the body lift...I didn't notice any problems. I've installed 2 of the same... -
Atturo TrailBlade XT
Just bought a set for my ecodiesel. 35 in mt. Love them so far. They roar a bit but that's to be expected. Will be a while before I get any milage reports on them tho. -
2015 ecodiesel build....
I was averaging about 20 before now I'm about 18. Most of my driving is on the interstate or in stop and go traffic. The interstate speed limit is 75 mph so that puts my rpms at 2000 to 2100. A little high for good fuel milage. My hemi that I traded in had the exact same gears and I averaged 12... -
Level & 3" Body Lift Pics Only
2015 ecodiesel with maxed 5100s and PA 3 inch body. 35 mt. With 20x10 -24 offset wheels...[ATTACH] -
2015 ecodiesel build....
Got wheels and tires finally. uca ball joints still look fine. Updated pick...[ATTACH] -
2015 ecodiesel build....
Think I need a rear spacer to give it a little rake. Don't need much. What does most people go with 1.5 in the rear? -
2015 ecodiesel build....
Fuel lethal 20x10 -24 offset. Gonna give those atturo trailblade mts a try in the 35x12.50 size. Planning on wearing those out and then going up later to 37s and adding 6in. Suspension. -
2015 ecodiesel build....
Haven't changed UCAs they don't look in a bad angle. Gonna keep an eye on them but if I notice anything I'm gonna replace them. -
2015 ecodiesel build....
took me a day and a half but got it done. 5100s at 2.8 and 3 inch body with gap gaurds. Thursday wheels and tires... -
2015 ecodiesel build....
Well went with 5100s and PA 3 inch body. PA says it's not 100% for the ecodiesel because of the fan shroud but it's minor to fix. 35s after that. Waiting on everything to come in now... -
2015 ecodiesel build....
With most lifts they come with coil spacers in the front. Would it be better to buy 5100s and use instead of the spacers? -
2015 ecodiesel build....
Thanks for for advice. Which ever way I go I will be installing everything myself. -
2015 ecodiesel build....
I may go this route. That's a clean looking truck.
Members online
- Mike1C5
- smithabs1963
- LeeD
- jawzs2
- fxnytro17
- Coachsully
- joesstripclub
- Mike Wenrich
- Raminit2014
- Mekcanix
- Treburkulosis
- Burton Shriber
- Kayswillden
- Travis8352
- Lsujker
- Chiphead7
- DaveNC
- 14 Lonestar
- Heatheroo
- Old Fart
- Adamcr68
- Calicajun
- Hardracer
- Edward Hands
- gwuhesos
- mb33458
- mvmike
- curtm295
- kad
- TeddysNof
- barr0208
- EagleChief
- GapperGus
- u2slow
- jtucker
- WAR-RAM
- HEMIMANN
- B0330
- victor26
- Lewybrewing
- duckman631
- Baker74
- danebrewsbeer
- Justin Stafford
- ABuchler
- Andrewpope101
- RamDiver
- Oleggmn
- mnewhard
- Jeepwalker