Wiring location for rf hub

[Jass Dhaliwal]

Hey everyone
I am installing push button start system with proximity handles to my 2016 ram 1500. Can anyone point out the pins on rfid hub where wires from handle button(black button on handle that lock and unlock) and wires from proximity sensor in door goes.
Thanks for help
I uploaded the picture of said pins

 

[ric221]

Are you building your harness, or are you working with a premade setup?

 

[ric221]

There is a very good series of videos on YT that should get you up and going in no time. I just completed this very same process on my 2016. Just search for passive entry install on YT.

 

[Jass Dhaliwal]

Are you building your harness, or are you working with a premade setup?

It is premade but unfortunately the guy stopped responding. My push to start button is working. I just don’t know on which pins I connect these wires coming from door handles and antinas i connect my wires to. On module there are 12 pins. To 4 of them I connected wires coming from front and back antennas that are supposed to detect if key fob is inside. Now i have 8 wires left(4 from each handle)and 8 pins left on module.

 

[Jass Dhaliwal]

There is a very good series of videos on YT that should get you up and going in no time. I just completed this very same process on my 2016. Just search for passive entry install on YT.

I have been researching since day before yesterday in most of those videos plug that goes into module is premade. So now information about where each particular wire goes

 

[ric221]

can you post pictures of the wires spread out so they can be seen better

 

[Jass Dhaliwal]

can you post pictures of the wires spread out so they can be seen better

Watch unnamed | Streamable

Watch "unnamed" on Streamable.

streamable.com

I made a video it shows exactly what i am working with

 

[ric221]

My harness was premade also but I had to pin the connections for the ant. and the door handles through the B pillars for ant. and the A pillar for the Handles

 

[Jass Dhaliwal]

My harness was premade also but I had to pin the connections for the ant. and the door handles through the B pillars for ant. and the A pillar for the Handles

That’s exactly what i wanna know where those goes in. Sorry i am a complete noob to this so please be as clear as you can think you are instructing a 5 year old so which is B pillar and A pillar ??

 

[ric221]

I sent you a link to the videos that I used

 

[Black-Wolf]

I think this is what you're looking for...

 

[Jass Dhaliwal]

I think this is what you're looking for...

Yes i am looking for something like this but this one is for trucks with turn key start. I am looking for push button start one
Thanks

 

[Black-Wolf]

Yes i am looking for something like this but this one is for trucks with turn key start. I am looking for push button start one
Thanks

That's actually for both. The keyless is the shaded portion, the turn-key is to the left of that - unshaded.

 

[Jass Dhaliwal]

That's actually for both. The keyless is the shaded portion, the turn-key is to the left of that - unshaded.

Yes it does but it only has layout for the wiring coming from ignition not wiring diagram for wiring that comes from door handle and proximity antenna

 

[Black-Wolf]

Ah... here - take a look at this one then:

 

[M10rocko]

Black-wolf, where are you finding these pdfs? I'm looking for a few of them myself and I'm not finding any good ones

 

[Black-Wolf]

Black-wolf, where are you finding these pdfs? I'm looking for a few of them myself and I'm not finding any good ones

I found the entire wiring diagram pack about 6 months ago - not sure where. You can grab them yourself from my Google Drive here (note - they're all for 2017/4th Gen - but often do apply for 3rd and 5th Gen in many cases): 2017 YM RAM Wiring diagrams.

 

[M10rocko]

Awesome Thank you! I have an 18 eco so as you can guess I have been in need of lots of info and diagrams. Would you have any other information about any 4th gen repairs ect?

 

[Black-Wolf]

Awesome Thank you! I have an 18 eco so as you can guess I have been in need of lots of info and diagrams. Would you have any other information about any 4th gen repairs ect?

Most of it I get from doing online searches. If there's a specific one you're looking for, you can hit me up - I'm mostly an electrical type guy (used to be an aircraft electrician) - and my current day job is as a network engineer, so I understand the comms and electrical pieces better than most. I do some tinkering engine wise. When it comes to other things, I may or may not be able to help (for example: I know jack and squat about exhaust, but can muddle my way through. I know more about engines in theory and have even rebuilt the top end of one on an older Mazda B3000 I had - but I had help with that too). I've got some other files - but they're pretty incomplete. I'll see if I can dig them up.

 

[Jass Dhaliwal]

Ah... here - take a look at this one then:

This is the one
Thanks
I will hook up the wires once i go home