Recent content by quick6black

  1. Q

    P2314 ignition coil e secondary circuit

    Lucky me, in CT and need to take my truck through emissions. Already over due and cannot seem to get rid of this code. Replaced the all the plugs with champion copper core, New coil, New wires, replaced the fuel rail (rusted and leaking), also replaced the injectors with lower mileage...
  2. Q

    2004 1500 Part recommendations

    thanks for the recommendations, I will check out Rock Auto. I do agree with buying the steering rack locally. I have seen it in stock. Thanks for the help
  3. Q

    2004 1500 Part recommendations

    I have a 2004 Hemi 1500 4x4 automatic that I am trying to bring up to perfect operational standards and there are a few things I am apprehensive to replace with cheap reman parts. I need to replace the power steering rack and was wondering what other users have used that has been a good...
  4. Q

    2004 Hemi won't start

    what do you need an update on? My truck is starting with my jumpered hack. Sending 12 volts to the PCM on connector 1 wire 29 resolved all the issues I was having. So you are getting 12 volts on pin 13 under the IPM? There may not be voltage on pin 12, that could be connected to a relay or some...
  5. Q

    2004 Hemi won't start

    i had all the same symptoms, check earlier in the thread. I post a PDF which shows where to check for power on the PCM. that will help you trace which wire is not getting power. For me it was wire 29 on connector 1, the PDF has a diagram showing the wire configuration
  6. Q

    2004 Hemi won't start

    i ended up measuring the voltage on the underside of the fuse box in connector 1. it is known as Integrated power module connector 1, pin 13. I was only getting 2 volts. So I put a fusable link from the battery to wire 29 on connector 1 of the PCM and the truck started. The issue I am having...
  7. Q

    2004 Hemi won't start

    dodge wants $650 for a new one. Found a couple used ones for $115 and $200, both not near me. Father in law going to try to fix tonight, I am hoping I can get it fixed and then maybe pick a new one up later.
  8. Q

    2004 Hemi won't start

    I wish it was that simple...and cheap. Looking over how the box was constructed its no wonder it failed. Sealed from the top but open ports on the bottom. Going to see if my father in law can re-solder the connections, he has a degree in electronics. If not see how bad dodge is going to hit me
  9. Q

    2004 Hemi won't start

    I think i may have isolated the issue. I decided to take apart the IPM and found some corrosion. I attached some pics of the board.
  10. Q

    2004 Hemi won't start

    I took out the ICM and clean all the plug connectors using baking soda, blew them out with compressed air, and then used a thin file to scrape around in the female end of the connector. No change in behavior. Just for kicks i also replaced the ignition switch, also no change in behavior. I also...
  11. Q

    2004 Hemi won't start

    I know the lights work, will check the horn and turn signals tonight.
  12. Q

    2004 Hemi won't start

    my dash lights up, odometer also turns on, my gauges do not work. Volts does not come up with accessory power on and the shift indicator square is also not showing. The 12 volts on the PCM is really what I am thinking is the issue. From how I interpret the issues if the PCM is not getting 12...
  13. Q

    2004 Hemi won't start

    Attached is the plug identification chart Chris from Hot Wire Auto sent me. I have checked the voltage on all the fuses in the IPM and I am getting 12 volts. I also pulled the unit out and checked all the plugs and they appear to be in good shape. How can you tell if the IPM has failed? I need...
  14. Q

    2004 Hemi won't start

    Sorry for not responding. I have been digging a bit, trying to diagnose the issue. I contact Chris at Hotwire Auto and he sent me a chart to test the PCM. I am not getting 12 volt constant on harness 1 pin 29 of the PCM. So I figured a short somewhere in the system or a blown fuse. I checked all...
  15. Q

    2004 Hemi won't start

    Another symptom I noticed a little while ago ( not sure if related ) was the intermittent wipers timing was weird. I would get 3 fast wipes then nothing for a bit, another 3 fast wipes. When I talked to Dodge they said that my ODB2 connection error can be another module trying to communicate...
See more

Latest posts

Members online

Total: 785 (members: 21, guests: 764)
Robots: 1,485

Forum statistics

Threads
195,849
Posts
2,875,158
Members
156,819
Latest member
vishalroy

Share this page

Top