Recent content by Jason157E

  1. Jason157E

    Factory 30K 5th Wheel Hitch Torque Specs

    I have a factory Mopar, 30K 5th wheel hitch and am needing to adjust the platform up two holes. Does anyone know the torque values of those four bolts? Thanks in advance.
  2. Jason157E

    Fuel pump recall

    Thanks...I'll check it out!
  3. Jason157E

    Fuel pump recall

    I spoke with two separate dealerships today and both told me the 2019s have been removed from the list as "no solution is available". They also said nor is a solution in the foreseeable future. So, those of us with 2019s, what do we do now? Just wait till it fails? With 121K miles I don't...
  4. Jason157E

    Gooseneck Ball Removal

    Thanks to everyone for the ideas. I had to abandon the project for now as I am expecting a call to pick up our fifth wheel any day now and the weather turned to crap again. I did soak down through the hole with Kroil and tried to beat it out from the bottom but to avail. It's hard to get a...
  5. Jason157E

    Gooseneck Ball Removal

    UPDATE: Today is above freezing so I went out and looked into it a little deeper. The ball was a Curt 2 5/16". The ball freely rotates by hand and has approx. 1/32" of freeplay up and down. Not enough, unfortunately, to try and pry up on it. I used a flashlight and cannot see if anything is...
  6. Jason157E

    Gooseneck Ball Removal

    True. I bought this from a dealer who probably knew even less about it than I did. The fifth wheel hitch covered it up. I only need the fifth wheel but, you're right, it's the principle of it!
  7. Jason157E

    Gooseneck Ball Removal

    Thanks. I just checked it out but being the top is cut off it's hard to tell if that's the type I have. Of course, the hole down the center could be an indication it is. It's snowing right now but I will get up in the bed, first chance I get, and see if I can see if there is anything left of...
  8. Jason157E

    Gooseneck Ball Removal

    I just went out and looked but I do not see any locking cross bar in either rear wheel well. Does that make this a screw in type or another type of retention?
  9. Jason157E

    Gooseneck Ball Removal

    Good morning, all! You folks have been so helpful with my other issues I thought I would include everyone with my latest calamity! My 2019 3500 has the max tow package. I am the second owner and believe the original owner was a Hotshot who used both the gooseneck, as well as the fifth wheel...
  10. Jason157E

    DPF Full See Dealer Message

    Actually, I did just this. I use the wife's ride daily, since she works from home, and we take the truck on rides longer than half hour or so. Thus far it's been working out.
  11. Jason157E

    DPF Full See Dealer Message

    In the final analysis that is what I done. 119K miles and this DPF was done. $3500.00 installed including the ECU refresh back to stock. Drove it home and it threw a code for the DEF system. Drove it back and turns out the DEF injector was crystallized shut from being turned off so long...
  12. Jason157E

    2019 RAM 3500 8.4 Uconnect (Non-Nav) screen issues.

    Sorry Johnny...I missed your reply. I figured it out. The whole dash section had to come out and the unit removed. It was probably no necessary but made for a much nicer install with no trimming. Thanks to all who recommended these Matte Screen Protectors! They took a couple weeks, coming...
  13. Jason157E

    DPF Full See Dealer Message

    I'm beginning to see what you mean, lol.
  14. Jason157E

    DPF Full See Dealer Message

    Thank you!
  15. Jason157E

    DPF Full See Dealer Message

    I'm leaning toward, and currently looking for, a beat'er. Can you recommend an OBDII Adapter and App.? There are several to choose from and I am not sure if it matters which one I choose for my 2019. Thanks!
See more

Latest posts

Staff online

Members online

Total: 1,351 (members: 43, guests: 1,308)
Robots: 1,809

Forum statistics

Threads
195,638
Posts
2,872,802
Members
156,469
Latest member
amadhi89

Share this page

Top