Recent content by Midnight 4x4

  1. Midnight 4x4

    La 318 to 360 magnum

    my 318 started to leak from the front and rear main seals so instead of fixing it I’m going to swap to a 5.9 magnum. I have looked into this swap and want to avoid as much computer junk as I can so I’m going with a carburetor and a la distributor. My question is will I need the crank position...
  2. Midnight 4x4

    Could newer ram spindles fit

    I was wondering if spindles from lets say a 02 -08 Ram 2wd could work with minor modification if any. Only thinking about this cause I want better brakes on the front and possibly raise the nose a little
  3. Midnight 4x4

    where to get parts

    Are you looking for the leaf spring mount of shock mont? Have you called/looked local pull a part?
  4. Midnight 4x4

    Lowering questions with D100

    I meant the truck lower control arm mount has to be drilled out to 3/4 in an trim around the van arm that goes in truck mount
  5. Midnight 4x4

    Lowering questions with D100

    On rockauto b250 lower control arms are less than $40. This is all the mods I had to do to them. The mount on the truck needs to be drilled out to 3/4in for van LCA
  6. Midnight 4x4

    Is there a better coil pack that stock

    Alright good to know I thought that there would be something better but if stock fine I’ll leave it alone
  7. Midnight 4x4

    Is there a better coil pack that stock

    Sorry if this is already on here. I was wondering if there are any aftermarket coil packs that could improve performance. Also are there better spark plugs. My truck is about to roll 75k think its about time for a revamp.
  8. Midnight 4x4

    1985 Lowering Questions.

    shackles are for a chevy a little wider than ours just ground them down to fit in the mount. It leveled the truck out kinda. Not low enough for me. LCA on the front just complete. Have to drill 2 - 1/2” holes by ball joint to match strut arm. I’m not sure if it is a steering stop but cut it off...
  9. Midnight 4x4

    1985 Lowering Questions.

    I used the cheap ones drone oreillys there were like 40 bucks. Had a hard time getting the bolts out cause they probably had never been jacked with before. Also installed van lower control arms and its super easy to do don’t let them fool you don’t go to pull a part for the control arms. Rock...
  10. Midnight 4x4

    1985 Lowering Questions.

    Sounds like we have the same truck I’m in the same boat as you. I put lowering shackles on the rear and they leveled it. That is not low enough I’m going to be trying the van lower control arm route this weekend and see how that goes. I will inform you on my struggles as they approach.
  11. Midnight 4x4

    1st gen 96 dodge ram lowering question(s)

    Flip kit will give a little more than 3in in rear
  12. Midnight 4x4

    What is with the cpu on carb

    Ya its part of the air cleaner
  13. Midnight 4x4

    Whining noise coming from engine

    Ok I’ll try that when I have a chance thnaks
  14. Midnight 4x4

    Whining noise coming from engine

    I thought it might be drivetrain be they said it wasn’t so I’ll probably just replace the cheapest part first and go from there and it’ll probably be the drivetrain
  15. Midnight 4x4

    Whining noise coming from engine

    I have a 2014 ram 5.7 4x4 there has been a whining noise sounds like its coming from the engine bay. I was told by the dealership that it was idler pulley so I replaced that was not the problem. It get louder with more rpm. It has nothing to do with it being a 4x4 cause it makes the noise in and...
See more

Latest posts

Members online

... and 2 more.
Total: 1,286 (members: 52, guests: 1,234)
Robots: 1,848

Forum statistics

Threads
195,684
Posts
2,873,295
Members
156,552
Latest member
JakeFox

Share this page

Top