Go Rhino 2.0 Installed

Navy Six Zero · Jan 5, 2019

I will, have to finish my interior first-got all the goodies to swap out all that nasty beige upper treatment to all black, then I am seriously thinking about a 1.5 body lift on top of the 6"-still have a slight tire rub...

See you out there brother!

magician · Jan 5, 2019

radkawi said:
Awesome! Happy to have helped.
Post up your pictures once you got it mounted. You'll be amazed at how good it looks once installed.

When you were looking did you check any from Black Horse? I’m looking at the Armour and Atlas for my truck. Not quite as pricey and may look better on my 2wd..

radkawi · Jan 5, 2019

magician said:
When you were looking did you check any from Black Horse? I’m looking at the Armour and Atlas for my truck. Not quite as pricey and may look better on my 2wd..

I did for just a bit but I didn't care for having the brand name on the side plates and when the plates are removed I'd be left with the welded tabs hanging down. With this bar, when I remove the mess sides I just fill the nutserts with the supplied stainless hardware and I'm done. I was not a big fan of the mesh on this 2.0 bar either and planned to pull them off after I completed the install. Having it on a for a couple of days, I am now thinking of adding some side LED pods by cutting out a section of the mesh to accept them. For now they stay but easy to remove once I make up my mind.
Either of them would look great on your truck just depends on how you want it set up and that choice is the hard one to make sometimes. Post pics when you get it done. Would love to see it.

radkawi · Jan 5, 2019

Navy Six Zero said:
I will, have to finish my interior first-got all the goodies to swap out all that nasty beige upper treatment to all black, then I am seriously thinking about a 1.5 body lift on top of the 6"-still have a slight tire rub...

See you out there brother!

AWESOME! I did the same with the upper grey trim parts. Swapped to the limited black and had a local trim shop install an alcantara headliner. This is the way RAM should have built my truck!
Post some pics as you get 'em done.

8732cuts · Jan 5, 2019

I powder coated the mesh sides it came out nice but not I think I want another colour

Sent from my SM-N960U using Tapatalk

Navy Six Zero · Jan 5, 2019

radkawi said:
AWESOME! I did the same with the upper grey trim parts. Swapped to the limited black and had a local trim shop install an alcantara headliner. This is the way RAM should have built my truck!
Post some pics as you get 'em done.

View attachment 151206

I see we are on the same trajectory! The grey is a nice contrast.

Navy Six Zero · Jan 5, 2019

8732cuts said:
I powder coated the mesh sides it came out nice but not I think I want another colour

Sent from my SM-N960U using Tapatalk

You talking about the mesh grills on the bar correct? I was thinking of color matching to truck. It didn't come out the way you wanted?

radkawi · Jan 6, 2019

8732cuts said:
I powder coated the mesh sides it came out nice but not I think I want another colour

Sent from my SM-N960U using Tapatalk

Now there's an idea! Have any pics?

8732cuts · Jan 6, 2019

radkawi said:
Now there's an idea! Have any pics?

Here's one zoom in, I have the lights lowered,

Sent from my SM-N960U using Tapatalk

2010 Infantry Vet · Jan 6, 2019

radkawi said:
Doesn't interfere with the third lamp.

View attachment 151037

Well i officially now know this go rhino bar will not work with the rambox. Thanks for the pics

radkawi · Jan 6, 2019

8732cuts said:
Here's one zoom in, I have the lights lowered,

Sent from my SM-N960U using Tapatalk

That looks great. Truck is bad ass! Two story storage in the bed, that's awesome!
Thinking of cutting out for some pod LEDs so your powder coat idea fits the bill to repair what I'd hack up.

radkawi · Jan 6, 2019

2010 Infantry Vet said:
Well i officially now know this go rhino bar will not work with the rambox. Thanks for the pics

Bummer!

8732cuts · Jan 6, 2019

Rambox doesn't come back that far does it. I think you would have to it's only about 18" I could measure to give you exact dims

Sent from my SM-N960U using Tapatalk

8732cuts · Jan 6, 2019

radkawi said:
Bummer!

That's another reason for the extras storage above bed I have my cube side lights on the side and a 40" in the back behind the flag, the flag is meshed and I spray painted the Texas flag on it, I can also hinge the rear mesh on the rack but it doesn't block the light when I use it. Zoom in I think you can see them.

Sent from my SM-N960U using Tapatalk

Porkbutt · Jan 7, 2019

Looks really good!

bigred74 · Jan 7, 2019

I was torn between old school and led bar so decided on the pro6 light bar. Just need to get some time to design the mounting brackets and have a local place make them up for me. Welcome to the go rhino club

8732cuts · Jan 7, 2019

Do you have the actuator? The can mount directly on there

Sent from my SM-N960U using Tapatalk

8732cuts · Jan 7, 2019

8732cuts said:
Do you have the actuator? The can mount directly on there

Sent from my SM-N960U using Tapatalk

I had extra one in my garage.

Sent from my SM-N960U using Tapatalk

bigred74 · Jan 8, 2019

How you manage to get an extra one? Lol and yea I have it. Just need brackets made for the light

IRSmart · Jan 8, 2019

radkawi said:
Doesn't interfere with the third lamp.

View attachment 151037

It covers the light if you have the cargo camera, because the brake light LEDs are mounted higher up on the lamp assembly. I removed all the tacky looking go rhino name plates and I’m looking for an alternate lighting solution for mine to mount where the large logo used to be

Go Rhino 2.0 Installed

Member

Senior Member

Senior Member

Senior Member

Senior Member

Member

Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Member

Senior Member

Senior Member

Senior Member

Senior Member

I drink and I know things

Similar threads

Forum statistics

Share this page