Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Hagar1

Senior Member
Joined
Aug 9, 2023
Posts
1,297
Reaction score
2,798
Location
Ontario Canada
Ram Year
2012 Ram 1500
Engine
Hemi 5.7
Yeah that setup looks like it would work well. In hindsight, cutting the old ones off is pretty easy if you just jump right to that - if you wanted to skip buying one. But adding one of those to the kit would be nice.

This torquing the pinion nut is is the real beast part though - mainly because I'm on stands. If it was on a lift, I'd be done today. It is a crap ton of torque - 200-300ft lbs, on a freely rotating yoke. This is how the manual shows to do it, with the Mopar special tool - that guy must be WAY stronger than me. But again, much easier with lift clearances and working room - and I'm not especially strong to begin with.

View attachment 592551
I've used that set up a lot of times.
If you can get the MIG welder into the outer race, run a bead all the way around, it often helps loosen the bearing to the point it will almost fall out. just run the bead in the center of the race.
 

Hagar1

Senior Member
Joined
Aug 9, 2023
Posts
1,297
Reaction score
2,798
Location
Ontario Canada
Ram Year
2012 Ram 1500
Engine
Hemi 5.7
Yeah that setup looks like it would work well. In hindsight, cutting the old ones off is pretty easy if you just jump right to that - if you wanted to skip buying one. But adding one of those to the kit would be nice.

This torquing the pinion nut is is the real beast part though - mainly because I'm on stands. If it was on a lift, I'd be done today. It is a crap ton of torque - 200-300ft lbs, on a freely rotating yoke. This is how the manual shows to do it, with the Mopar special tool - that guy must be WAY stronger than me. But again, much easier with lift clearances and working room - and I'm not especially strong to begin with.

View attachment 592551
What the heck happened? I offered an time tested method of removing a bearing race and my comment got kick and a warning came up.

Then, just as suddenly, it came back.
 
Last edited:

Wild one

Senior Member
Joined
Jan 17, 2016
Posts
24,681
Reaction score
57,958
Ram Year
14 Sport
Engine
5.7
I've used that set up a lot of times.
If you can get the MIG welder into the outer race, run a bead all the way around, it often helps loosen the bearing to the point it will almost fall out. just run the bead in the center of the race.
We used to cut the outer race and bearing cage off,then run a bead of weld around the inner race,and like you said a couple good whacks with a hammer and chisel would usually pop the race off.
We used to change alot bearings in the farming community,and that old school trick always worked when you were changing a bearing in a field where there were no presses available to push a bearing off,or removing the shaft the bearing was on wasn't an option,like on a combine
Alot of the old school tricks that still work to this day seem to have gone by the wayside :rolleyes:
 

Hagar1

Senior Member
Joined
Aug 9, 2023
Posts
1,297
Reaction score
2,798
Location
Ontario Canada
Ram Year
2012 Ram 1500
Engine
Hemi 5.7
We used to cut the outer race and bearing cage off,then run a bead of weld around the inner race,and like you said a couple good whacks with a hammer and chisel would usually pop the race off.
We used to change alot bearings in the farming community,and that old school trick always worked when you were changing a bearing in a field where there were no presses available to push a bearing off,or removing the shaft the bearing was on wasn't an option,like on a combine
Alot of the old school tricks that still work to this day seem to have gone by the wayside :rolleyes:
I've had it work well without needing to cut into the bearing race, when the weld cools it "shrinks" ever so slightly and usually does the trick.
Yes indeed, a lot of the old tricks have fallen by the wayside.
 

Wild one

Senior Member
Joined
Jan 17, 2016
Posts
24,681
Reaction score
57,958
Ram Year
14 Sport
Engine
5.7
I've had it work well without needing to cut into the bearing race, when the weld cools it "shrinks" ever so slightly and usually does the trick.
Yes indeed, a lot of the old tricks have fallen by the wayside.
In the field it was more common to have a stick welder then a mig,and to get a stick into a bearing race usually wasn't an option,so you cut the outer race off either with a torch or a side grinder ;)
 

pacofortacos

Senior Member
Joined
Apr 18, 2017
Posts
3,918
Reaction score
5,020
Ram Year
2016
Engine
5.7
I did look at some videos about those after seeing your post - was curious what they did differently, and you're right - I wasn't understanding how it worked. This youtube video does a really good job of explaining and showing the details of how it works and where it's engaging. It actually is pulling on the cage (which would totally explode if you did it with a simple puller) - but by sandwiching the whole bearing with cone in position within the tool, it makes that work and generally doesn't even damaging the bearing. It's cool - it sandwiches it with a big ring, but it *also* compresses the cup on the cone like it's assembled in the truck. Pretty clever.

Good to know for next time! My 2014 only has about 90k miles on it - but almost 30k is towing a 7000lb trailer around the country, so I guess that's fair to have cooked 2 bearings. Axles and wheel bearings weren't even bad though.
What gear oil are you using? I prefer Redline and still change it every 3 years.
 

Hagar1

Senior Member
Joined
Aug 9, 2023
Posts
1,297
Reaction score
2,798
Location
Ontario Canada
Ram Year
2012 Ram 1500
Engine
Hemi 5.7
In the field it was more common to have a stick welder then a mig,and to get a stick into a bearing race usually wasn't an option,so you cut the outer race off either with a torch or a side grinder ;)
Yes, I can understand that problem. Back in the day when I worked in a truck shop, we did not have a MIG only a stick welder. I remember using the torch on occasion. I worked for one guy who would use a big hammer to crack the bearing inner race, that is how I acquired the steel splinter in my wrist.
There were several methods, some more effective than others.
 
OP
OP
C

chili81

Junior Member
Joined
Nov 3, 2026
Posts
15
Reaction score
23
Location
Connecticut
Ram Year
2014
Engine
5.7 Hemi
Yes, I can understand that problem. Back in the day when I worked in a truck shop, we did not have a MIG only a stick welder. I remember using the torch on occasion. I worked for one guy who would use a big hammer to crack the bearing inner race, that is how I acquired the steel splinter in my wrist.
There were several methods, some more effective than others.
I only have stick or flux too - and very limited skills with either. Sounds like a good trick though to keep in mind for the future.
 

Forum statistics

Threads
213,354
Posts
3,092,143
Members
174,575
Latest member
DITRIO
Back
Top