Search results

  1. gearhead

    2003 4.7 Throwing P0302 Code ADVICE!!

    For sure. Depending on your mileage it doesn't hurt to get them sent in and done at a local shop. They come back brand looking. Here in AZ I got them done for 18.00 per injector and had them back same day. I hope yours smooths out. I have heard of crank sensor causing some idle issues but who...
  2. gearhead

    2003 4.7 Throwing P0302 Code ADVICE!!

    Got the injectors back and the one injector was faulty at idle so it was replaced. Everything installed again and truck runs like a top again! Starts instantly and runs smooth, seems to have a little more juice. Hopefully this thread can help someone else looking to solve this code issue.
  3. gearhead

    2003 4.7 Throwing P0302 Code ADVICE!!

    Just an update on this issue. Pulled plugs. The one plug from the bad cylinder for sure was lighter in color and was missing the distinct burn mark the others had. I pulled the injectors and sent them in for be gone through and flushed the fuel rail. I will putting in new plugs and checking the...
  4. gearhead

    2003 4.7 Throwing P0302 Code ADVICE!!

    Thanks for the advice. I am going to pull the plug to and that should tell me something. I keep thinking it is something electrical since it is such a slight miss and so random. I would think if it was a lifter or fuel injector it would be constant I am also going to get my hands on my...
  5. gearhead

    2003 4.7 Throwing P0302 Code ADVICE!!

    Hi Guys, I have a 2003 4.7 2wd. A few months back the truck threw P0302 code. So I thought lets eliminate the obvious first. Checked the plugs and they were nubs! I had no idea this truck had copper plugs and it went 60k on factory plugs. I swapped them out and cleared the code and it was...
  6. gearhead

    3rd Gen RamRunner

    Incredible truck! This truck will shut the chevy and ford guys up! I'd take this over a raptor any day!
  7. gearhead

    2WD Lift

    Then it sounds me like a spacer is not the option for you. The most you will get for an 02 ram is 1.5" which is hardly a lift, more of a level at best. Check out CST website. I had the best luck with them. Also Rough country and I think fabtech offer 6inch lifts if you want to sky it out.
  8. gearhead

    2WD Lift

    Thats a pretty open ended question. If you are comparing a spindle lift with a spacer lift, then on a 2wd, there is no comparison. Only thing a spacer lift does better is save you money. Spacers will reduce the travel in your front suspension. Now it also depends on the year you have. Mine being...
  9. gearhead

    Leveling Kit

    There are a TON of leveling post on here where everybody gives the same advice on a weekly bases. Just scroll down and read through some. Personally I would NOT do a spacer kit on a 2wd. I tried installing a Daystar on my 2wd and it screws the angle of the upper arm and ball joint. Solution...
  10. gearhead

    2WD Lift

    It's basically been said but it just drops the spindle location down which lifts the truck. The great thing is it does not change the factory suspension or geometry. If you run the spindle lift and combine it with the CST upper for extended travel and strength you would be more then set for...
  11. gearhead

    2WD Lift

    One of the best lifts out there for 2wd dodge ram is the CST Spindle lift. 4" and 6" I believe, I know 4" for sure. Keeps factory ride, direct bolt on, no brake line extenders or new shocks. BUT and this is important, IF you do a spindle lift DO NOT GO ON EBAY FOR THE CHINA MADE CRAP. Spend the...
  12. gearhead

    Trouble with plastidip on bumpers

    I did my front and rear bumpers. Big key is just use rubbing alcohol like mentioned above to clean them and if you mask off the lights, which I suggest, you need to peel them before the dip dries. It's the opposite rules as paint. So lay a thicker layer around the light right off the bat and...
  13. gearhead

    Opinions.

    It came out nice!
  14. gearhead

    blisteins vs leveling blocks

    I am assuming you meant to post this in the 4th gen lifted section but I would say the Bilsteins are a nice was to go. You can simply adjust them down and you don't have to worry about some spacer stuck above your coil. It is the way I would go, but as with any spacer style lift you will be...
  15. gearhead

    Lifted 3rd Gen Pics - Show Em Off!

    Who built that setup for you? What was the cost if you don't mind me asking? Thanks!
  16. gearhead

    Need your help with this

    Ya I had considered that, thanks for the input, it is a good approach. I appreciate it.
  17. gearhead

    Need your help with this

    I have been looking everywhere for a spindle lift for my 2003 2wd 4.7 1500 ram. I found CST and would go with them except they say you can't run more then 4.75 back space and my KMC wheels are 5.00. So I came across chasis tech 3" lift spindles, no back space required. But they are WAY cheaper...
  18. gearhead

    Tail Covers - Yes or No?

    I am honestly digging the factory lights! Either way you can't go wrong but that truck is so clean to begin with sometimes less is more. Looks super clean with the factory tails.
  19. gearhead

    Tail Covers - Yes or No?

    I've never been a fan of tinting the lens. If anything I would say black housing with clear lens. People drive stupid as it is and it would suck to get rear ended because the tail light wasn't bright enough. BUT that's just my own person pet peeve I have with them.
  20. gearhead

    Anybody have any idea what rims these are?

    Those are them! I think that is what was pictured, IMO.
  21. gearhead

    Did some plasti dip to my emblems

    Great! It works really well. Nice job on the truck!
  22. gearhead

    Did some plasti dip to my emblems

    Yea it is VERY close. Only difference is it is matte finish, but you can purchase a gloss coating through dipyourcar.com if you want. I am going to get mine powder coated when it cools down here in AZ but for 10 bucks they came out great! The biggest thing is make sure you mask off what you...
  23. gearhead

    32" LED light bar installed

    Great, Thank you for the reply. And nice job fabbing the mounts. They look clean.
  24. gearhead

    Anybody have any idea what rims these are?

    They Look like Discount Tires brand. I would search them because they don't have bolts along the outside.
  25. gearhead

    Did some plasti dip to my emblems

    Use a tooth pic to get the centers of the letters out. This stuff works great. I plasti dipped my front and rear bumpers white to match my truck and I haven't been disappointed yet!

Latest posts

Staff online

Members online

... and 19 more.
Total: 1,423 (members: 69, guests: 1,354)
Robots: 1,546

Forum statistics

Threads
195,764
Posts
2,874,262
Members
156,680
Latest member
revrudolph

Share this page

Top