ball joint
-
D
2022 Ram 3500 Ball Joints
Have a 2022 Ram 3500 SRW w/ Cummins 6.7 in it; bought new and just turned 22,000 miles. Took it to tire shop to check alignment and get tires rotated and they said both upper and lower ball joints on both sides are worn to the point they can't align it. We work with this shop often and they have...- de_hokie_farmer
- Thread
- 3500 ball joint
- Replies: 9
- Forum: Heavy Duty
-
2
Can I do my ball joints without a press?
Hey all. 98 ram 1500 4x4 here. I am currently very broke. But also in desperate need for some new ball joints and wheel bearings. So I got the extra money together to buy 2 new wheel hub assemblies and upper/Lower ball joints. But I'm too broke to rent the press at the moment. I probably won't...- 2ndgenproject
- Thread
- 2nd gen ball joint
- Replies: 8
- Forum: Engine & Performance
-
replacement ball joint question
replaces my ball joints this week and everything went better than I thought it would however there is one thing I'm not sure about. the nut on the lower ball joint that's meant to hold it on is some type of lock nut and only barely gets on as when you try to tighten it the bolt of the lower...- VFDPrim
- Thread
- ball joint lower ball joint
- Replies: 1
- Forum: General Discussion
-
Stuck upper balljoint
I was trying to replace the upper control arm on my 15 Ram and I have thrown every hammer (that I can swing at it) separator tool (with air) and can’t get it to break free. I’ve done them a few times before on older Dodges but never had this much trouble. Any suggestions? -
Possible ball joint issue
I have a 2012 1500 with a 4inch procomp spacer kit with bils up front set to to 1.2 to level out the truck. my steering wanders left and right when I drive and im thinking that it could be blown ball joints. does anyone have any insight as to what it could be?? ill post some pictures of the... -
J
2 inch leveling kit
I just installed a 2in motofab spacer leveling kit. Just wondering how bad I will be affected with the geometry. How important is it that I should change upper control arms or will I be okay with stock uca. I don't do any off-roading. -
Bent Lower Control Arm
Guys, need some advice/help. So i raised the front end on my 04 Ram 1500 4X4 with a 2 inch level kit (torsion keys) and the rear with 2 inch blocks on the leaf springs and it looks great. Ever since then ive been blowing out cv boots (minor tears really). When i got the truck i slid off the... -
K
Lower Control Arms/LCA Skid Plates
I've done some deep googling and forum hunting and come up with nothing. I understand that our stock LCA angles dont need any correction with adjustable struts, but cosmetically/lust for overbuilt gear has me hunting. When I get my prerunner bumper on, they are going to be exposed for everyone...- Kyle McWilliams
- Thread
- ball joint control arm controlarms long travel lower control arm
- Replies: 6
- Forum: Exterior
-
Anyone have experience with "Synergy" HD steering kit and/or balljoints?
Hello, I am needing to replace tie rod ends and balls joints, among many other things. I am looking for anyone who has experience and opinion on the Synergy products. I'm thinking of getting the Synergy HD steering/drag link kit, to replace the OE. I do have a 2008 Ram 2500 5.7L 4x4, it looks...- Ghostman
- Thread
- ball joint control arm steering synergy upgrade wheel bearings
- Replies: 0
- Forum: Heavy Duty
-
E
2005 1500 4 wheel drive - transfer case issues
Hello, I have a 2005 1500 with a 5.7 and have been having some 4x4 issues. When in 4H the truck will bind up in reverse and in a turn of any kind so much so that I have to give it a lot of throttle to move in reverse and it will just push straight on snow/ice in a turn at slow speeds. It seems...- Eric CDA
- Thread
- 2005 ram 4x4 ball joint suspension transfercase
- Replies: 0
- Forum: Engine & Performance
-
M
Ball joint recall
Glad to find this forum. I've been browsing for the past few hours and there is a ton of great information here. I'd like to ask some of you your opinion about an issue I'm having on my 2006 with the 5.9L. I bought the truck a little over two years ago. After I bought it I was looking for...
Latest posts
-
-
INFO - 2013-2018 8.4A /AN FW Notes (RA3/VP3-NA & RA4/VP4-NA & UAx)
- Latest: OasisNinjaBat
-
-
-