Recent content by RAM_Designs

  1. RAM_Designs

    Yet another oil thread..

    RedLine Heavy Shockproof...toss in a quart or two when you put new gear oil in. Worked for me.
  2. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    Nah, they use 304 SS which is pretty rust proof, and we don't have any salt down here, so it'll definitely last the 5yrs I'll have them on for without any issues.
  3. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    Then don't buy them? Your decision, but I'm putting headers on mine.
  4. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    ARH and AFE offer both options, with high flow cats or without.
  5. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    yeah I wanted to go short for the money savings, but went with the ARH with high flow cats, got some attachments for the o2 sensors from Vivint(sp?) that allows you to adjust the air flow by the o2 sensor to keep them from throwing codes since there's more air flow through the LT system.
  6. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    The headers are made for the 6.4, there’s 3-4 companies that make LT’s for the 6.4 trucks. Also the stock exhaust on the 6.4 is 3.5”. I’m glad you felt a difference with the TB and CAI. I’m torn in the CAI because I think the stock one is designed very well.
  7. RAM_Designs

    To 87mm TB, or not to 87mm TB?

    Hey guys, been a while since I've posted here....I've FINALLY found someone local to install my ARH long tubes on my 6.4, it's the only real performance mod that I'm going to have done (aside from 4.88 gears). I'm not going to get a tuner, so with that in mind, since I have an easier flowing...
  8. RAM_Designs

    Trans service

    Just do both filters now, get that break-in stuff out of there so you don't have to worry about it anymore. Then every 60k just do a standard drain/fill without dropping the pan to get some fresh fluid in there. Should be fine.
  9. RAM_Designs

    HEMI 5.7 or 6.4

    2016 6.4 108k zero issues. 2003 5.7 400k zero issues. 2015 5.7 115k lifters and cam replaced at 105k ($4000).
  10. RAM_Designs

    Yukon vs G2 or Richmond gears?

    Use factory AAM gears if you’re going 4.56 or 5.13, only use something else if you’re going for something in a non-AAM size like 4.30 or 4.88 I personally use Yukon 4.88’s.
  11. RAM_Designs

    2016 RAM 6.4 TUNER OPTIONS?

    Well, I pulled the trigger on the ARH long tube headers, and I plan on getting an 85-87mm throttle body as well to get a little more intake velocity. I’m really not super concerned with getting the absolute most performance, more concerned about longevity and I mainly just drive highway miles...
  12. RAM_Designs

    Oil weight question

    I would personally grab a 5qt jug of Castrol Edge or QSUD 5w30 and add 2qts of Redline 5w30 to it to bump up the moly and calcium a bit....if you don’t want to spend the money on a full Amsoil/Redline change. This last time I did Castrol Edge 0w40 and Redline 10w40 for my 6.4, and it seems to...
  13. RAM_Designs

    Idle hours VS drive hours

    I would never ever ever run a 5w20 in a hemi, period. I'd bet money that the manual allows use for 5w30 and 10w30 depending on temps as well.
  14. RAM_Designs

    Header options for 6.4L nowadays...AFE, ARH, OBX...anything else?!?

    yeah I know about ARH, and I really like them, I'm just hoping to find some equally good options that don't cost 2k :/
  15. RAM_Designs

    Oil temp waaaay to high

    My 6.4 HD runs in the 220's when cruising highway speeds, mid 230's when towing...usually stays 20-30*above coolant temp.
See more

Latest posts

Staff online

Members online

Total: 1,235 (members: 47, guests: 1,188)
Robots: 1,805

Forum statistics

Threads
195,659
Posts
2,873,029
Members
156,510
Latest member
crxpd

Share this page

Top