Detailing: How to Claybar/Favorite Product

Discussion in 'Detailing' started by Trupiano, Sep 4, 2012.

Favorite Clay bar Product

  1. Adams Detailing Clay Bar

    14.2%
  2. Meguires Smooth Surface Clay Bar

    35.8%
  3. Mothers California Gold Clay Bar

    31.1%
  4. Other

    18.9%
  1. Kinetic

    Kinetic Junior Member

    Posts:
    22
    Likes Received:
    6
    Joined:
    Feb 8, 2015
    Ram Year:
    2015
    Engine:
    Hemi 5.7
    No. Wash, clay, re wash or QD wipe, compound (if needed), polish, then wax.
     
  2. TripleC5

    TripleC5 Junior Member

    Posts:
    9
    Likes Received:
    1
    Joined:
    May 23, 2015
    Ram Year:
    2013
    Engine:
    Hemi 5.7
    Just used clay bar last nght for the 1st time. (on my truck, and wife's car). I am very impressed at the difference in feel and appearance. I also used sealant and wax. It's like a new vehicle!
     
  3. rablwo

    rablwo Junior Member

    Posts:
    27
    Likes Received:
    1
    Joined:
    Mar 30, 2014
    Ram Year:
    2014 1500 Sport CC 4X4
    Engine:
    5.7 Hemi
    I am still trying to get my mind around a clay bar. It seems that many are nearly obsessed with cleanliness of their microfiber towels and wash mits; i.g. two bucket wash, grit gards, quality of towels etc.

    Yet, the clay is used to remove stuff. I assume that the stuff is impregnated into the clay. It seems to me that after a panel or two, you are just rubbing contaminated clay all over the rest of your truck. Wouldn't that cause scratches all over the place? How do you know when to replace your clay?
     
  4. tsc

    tsc Senior Member

    Posts:
    124
    Likes Received:
    34
    Joined:
    Jul 27, 2015
    Ram Year:
    2015
    Engine:
    Hemi 5.7
    The key to good clay bar is the lube. Make sure it's slick, when you slide the clay bar around and to make sure you fold the clay bar often (contaminated side to contaminated side).

    I've used Meguiar's and Mother's and have never scratched paint yet (I clayed about 20 times on my old truck--haven't used it on my new truck, but I've only had her a week and I'm on my "busy" week at work).

    The technique that I found that worked for me, was to grab a small chunk of clay (about the size of a Canadian toonie-- aprox 2"?) squish it to a pancake, thin enough to make it about 3-3.5" round, but not thin enough to see through it.

    Then spray the panel you are working on and give the clay a light misting on one side. Then start claying--wet side down. Aprox 1/3 of the panel done, I fold the clay and squish it out to form a pancake (like folding a pizza in half, all the "topping" are facing each other on the inside) and continue on. If you start to feel ANY drag... STOP!!!! and add more lube.

    Once I do one panel, I toss that chunk of clay and and get a new piece. I'm sure I'm burning though more clay then I could be, but a clay bar kit is about $20 and a new paint job is $$$$. I find that a bar of clay = one truck.


    I hope that helps.
     
  5. rablwo

    rablwo Junior Member

    Posts:
    27
    Likes Received:
    1
    Joined:
    Mar 30, 2014
    Ram Year:
    2014 1500 Sport CC 4X4
    Engine:
    5.7 Hemi
    That makes since TSC, treat the clay bar as a one use, disposable item. Thanks.
     
  6. 2014moparam

    2014moparam Senior Member

    Posts:
    255
    Likes Received:
    73
    Joined:
    Nov 17, 2015
    Ram Year:
    2014
    Engine:
    3.6 V6
    If i dont order online, the meguiars does OK, but I do like Pinnacle's claybar
     
  7. Pull Ya

    Pull Ya Supporting Member

    Posts:
    4,400
    Likes Received:
    2,351
    Joined:
    Jan 16, 2012
    Location:
    Cedar Creek, Tx
    Ram Year:
    2016
    Engine:
    5.7 Hemi
    Read about "Nano" towels. I think they work better than clay and are easier to use, at least for me. "autogeek" is a good reference source.
    Jay
     
  8. Jaded

    Jaded Junior Member

    Posts:
    8
    Likes Received:
    2
    Joined:
    Aug 7, 2016
    Location:
    Southern Maryland
    Ram Year:
    2013
    Engine:
    Hemi 5.7
    We use AutoScrub nanoskin on our buffer instead of a clay bar. SO MUCH faster and works better IME.

    P.S. Sorry to revive an old thread, but in my defense it is pinned. LOL!
     

Share This Page