Search results

  1. Cardsin2005

    LED turns and tails 2012 - Having issues with AlfaOBD changing the setting.

    4th Gen is 09-2018 and 2019-current classic.
  2. Cardsin2005

    LED turns and tails 2012 - Having issues with AlfaOBD changing the setting.

    I swapped in some LED turn signals and taillight bulbs, and I am having trouble getting rid of the hyper flash on my 2012 with AlfaOBD. I was able to fix this issue with my 2014 pretty easily with my 2014 truck. I know the computers are different and I was wondering if I was just missing...
  3. Cardsin2005

    IHC 3/5

    I had to go way back in to the archive for this. As you can see it is bolted up like normal. I have a jack lifting the lower control arm up to get the mounting hole for the end link closer to the sway bar. The sway bar is a big spring so when both wheels are at full droop like on a lift the...
  4. Cardsin2005

    IHC 3/5

    I didn't think about removing it in AlfaOBD. Do you know what codes have to be modified? I have been planing to remove diff at some point.
  5. Cardsin2005

    IHC 3/5

    I did not scrape on my steep drive or dips with the 3/5 and stock 275/65/20s. My 5/7 drop is another story. The crossmember in the front hangs really low on these trucks and that scrapes sometimes on my drive. But my tires are also a little too small. So a taller sidewall would help with that.
  6. Cardsin2005

    IHC 3/5

    IHC shocks are fine. Maybe a bit stiff but that keeps you from bottoming out.
  7. Cardsin2005

    IHC 3/5

    Sorry, this is an old post, but I did the 3/5 IHR kit than I pulled the front CV axels out and installed the Beltech 2in lowering shock for (the 4x4 rams) in the front and cut another 2 inches out of the IHR rear springs. You cannot go past a 3in drop in the front without pulling the CV axels...
  8. Cardsin2005

    Did Ram ever sell a regular cab truck with a center console

    That's great to know. Does anyone know the part number for the center consol end plates without the vents?
  9. Cardsin2005

    Did Ram ever sell a regular cab truck with a center console

    Hey all, I'm swapping a center console into my regular cab Express, and it got me thinking. Did Ram ever offer a center console option for regular cab trucks of any trim level? Looking through the different console end plates on moparpart I don't see any options WITHOUT rear vents.
  10. Cardsin2005

    7" EVIC backlight color

    Ya that is what I am used to with my 3.5" EVIC. I took another picture with the white balance adjusted to look more like what I see with my eye. It is defiantly warmer.
  11. Cardsin2005

    7" EVIC backlight color

    I just swapped clusters to a 7" EVIC. I noticed the white backlight of the gauges is slightly off white compared to my old 3.5" EVIC cluster. I am just wondering if this is how all the 7" EVICs are. The 3.5" EVIC was blinding at night so I wouldn't be surprised if they changed this later on. In...
  12. Cardsin2005

    IHC 3/5

    The front will be lower then a 3 inch drop without the isolator. "with Ride quality being the #1 goal. We achieved that by lowering the front end with custom control arms. You achieve the 4” with the lower control arm. We add 1″ spring isolater to set at 3″ (this is a quote from the IHC website...
  13. Cardsin2005

    IHC 3/5

    You rub with a 3/5 drop? That IS weird. When I was running the 3/5 I had the stock 275/60R20 size and had zero rub. Does it rub in the back or front? I did get an adjustable rear sway bar to re-center my rear end because the pass side tire would just kiss the lip of my bedside. The pic below is...
  14. Cardsin2005

    IHC 3/5

    Yup. Ride is great. Looks killer. Fits stock tire size. Upper control arms allow for camber adjustments. I did lower it another 2 inches in the front and rear and got much shorter tires.
  15. Cardsin2005

    Front wheel offset not even after lowering with IHC kit.

    After lowering my RCSB 4x4 with the IHC 3/5 kit. The drivers side front wheel is 1 inch farther in toward the engine then the passenger side wheel. Has anyone else experienced this? I know the IHC kit is designed to pull the front wheels in about 1/2 inch to give more room for wide wheels. That...
  16. Cardsin2005

    Strictly the 4x4 lowering thread...

    I am running the front half of the Belltech kit in conjunction with the whole IHC 3/5 kit. The IHC kit can be a 5-7 inch drop in the rear depending how much you cut the rear springs, so I am sitting at 5/7 now. The Belltech is much cheaper.
  17. Cardsin2005

    Strictly the 4x4 lowering thread...

    Looks great. I am quite happy with the Belltech kit. I only installed the adjustable struts in the front. I was surprised how normal the truck handled.
  18. Cardsin2005

    Strictly the 4x4 lowering thread...

    Yes my mistake I meant differential not transfer case. Thanks for the clarification.
  19. Cardsin2005

    Strictly the 4x4 lowering thread...

    It is not my daily. But yes I drive without the CV axles. There are sub shafts that stick out of the transfer case so there is no open hole into the case. Wild One gave me the idea after he told me he had removed his entire transfer case awhile back.
  20. Cardsin2005

    Strictly the 4x4 lowering thread...

    I have lowered the truck another 2 inches all the way around and had to remove the CV axels. Also put new Firehawk Indy 500s on it and the tires alone dropped the frame down another 2 inches. Still rides great.
  21. Cardsin2005

    Strictly the 4x4 lowering thread...

    Thanks! I do like the way it looks, and it rides fantastic. But I would like it to be a little lower so I can have a sportier size of tire on there without it looking too small.
  22. Cardsin2005

    Strictly the 4x4 lowering thread...

    I have been through this thread a few times, but from when it started to now it seems like things have changed quite a bit. I put the 3/5 Inez kit on my 4x4 RCSB. It rides great and look great as well. But I can't help but wish it was lower. I was DM-ing Wild One and he told me he removed the...
  23. Cardsin2005

    4 12s Behind the seat in a RCSB

    Thanks for all the awesome comments guys. I am working on designing a new 3D Printed dash pod that will fit a wider range of more common 3.5in speakers. I will have to do some test prints and see how they fit.
  24. Cardsin2005

    JBL MS-8 dsp for $130 Shipped (Receritified)

    Im not looking forward to re-building my trim panel I just finished. I won't need the 2 JBL units I have now. :disgust:
  25. Cardsin2005

    JBL MS-8 dsp for $130 Shipped (Receritified)

    Thanks for the heads up by the way.

Latest posts

Staff online

Members online

... and 12 more.
Total: 1,417 (members: 62, guests: 1,355)
Robots: 1,958

Forum statistics

Threads
195,639
Posts
2,872,818
Members
156,469
Latest member
amadhi89

Share this page

Top