I was looking to replacing the OEM EC module with another.
I am unable to provide the OEM No. to a parts store.
The parts department at dealership gave me a full page of possibilities of ECM's.
The OEM unit I have is ECM 542.
The seven digit OEM No. Is no longer visible on the sticker...
Just installed a new ignition switch to get the engine to turn over. The starter has power to turn engine over but no engine start. Engine was already timed to 10 degrees before TDC and ran well. Now my timing light picks up nothing and bulb does not flash.
What to check
Today I tried out the bulb type battery Tester. About $20 from NAPA. This Ultra Pro worked well in determining if my battery cells were in Good Fair or Low condition. All were fair except first cell. Rechecked first cell at the" fill-line" and it changed to fair condition. Still brought in...
Removed rear tail light harness from engine bay eight blade connector to tail lights. Resoldered weak connections I could find and tested continuity and 9 VDC tested on all wire circuits then covered wiring with plastic loomReinstalled harness along truck frame. Still no tail lights "on" when...
My first generation Dodge D 100 has the 5.2 litre (318 cc engine) the temperature guage needle moves to the right as engine warms up. I feel at 3/4 movement on guage shutdown engine should occur. At idle engine temperature is( just) below half . I have a new radiator, coolant set to -35 C...
It was going to get colder outside (-30C /- 25 F). I knew my Block heater cord did not work (circuit tester tested). So I was going to fish the three prong plug out. I tied a cotton string to the three prong plug in. I removed two zip ties off fuel line holding the block heater cord to it. A...
From ignition switch (DB) wire supply bus circuits:Interior dome light, wiper motor,, guages, back-up lights
From ignition switch (BK/WH)supply bus circuits: radio, turn signals, wipers
Other two bus circuits inside fuse block work: Headlights, horn, park lights, instrument panel lights. . ...
my switch has a purple, white and black wire connector, the harness dissappears under the floor hump. Anyone know where I can pick up the other end of this. harness trail on my '88 D100 5.2 liter and A 727 three speed transmission
D100 1/2 ton drove 120 Km/HR home. Next day drove a few feet and truck stopped moving. sensors: A/C relay (33), 14 MAP, 13 MAP and 12 (battery disconnect). Engine burning oil which is enough to fog yard in about five minutes.
Hi fellows.
Recently had my Dodge right bank head gasket replaced.
I have engine code 12 and 33.
Engine has noisy valve train unknown what side.
Engine has milky spatter on both cylinder head covers.
No. One has been averaged timed to 10 degrees before 10 T.D.C
Wiped down inside both...
Truck runs but valve train gets loud past idle speed. Recently replaced head gasket right cylinder head bank. Drove Ten miles and truck stalled every time I yielded or stopped. Oil pressure gauge at 30 to sixty PSI. Coolant temperature at 1/2 on guage. No check engine light codes. Around...
The emission label has a check valve. I am not sure by the drawing which way it is installed.
I ordered a check valve that its primary use is to advance the distributor.
Would this work here too.
I am missing the other part that goes into the solenoid holes, Just have the hose not...
I have a Dodge red truck. The rims supplied are steel and are white. I am looking to upgrade as they're looking shabby. It is hard to visualize which rim is well suited to this truck generation. Please answer my poll.
The engine leaks significant coolant fluid after 2 KM of driving around town. Recovered half pail of coolant from radiator petcock valve.
I then preceeded cylinder head removal with ancillary engine parts removal. Head does not come off gasket with block (2"x4") and hammer (14 lb) technique...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.