cam phaser

  1. T

    2021 5.7 Hemi already getting a top end rebuild, good to go or time to move on?

    My 2021 Hemi is getting a new cam, phasers, and lifters at 49k miles. Lucky for me the warranty hadn't run out yet. Everyone is telling me to tuck tail and sprint away from this truck the second it is out of the shop. Should I be genuinely worried about the rest of the engine going to crap, or...
  2. T

    2021 5.7 Hemi already getting a top end rebuild, good to go or time to move on?

    My 2021 Hemi is getting a new cam, phasers, and lifters at 49k miles. Lucky for me the warranty hadn't run out yet. Everyone is telling me to tuck tail and sprint away from this truck the second it is out of the shop. Should I be genuinely worried about the rest of the engine going to crap, or...
  3. S

    2015 5.7 (NOT) timing issue **Rebuild**

    Good afternoon all I have a 2015 5.7L that used to be a police truck. So it has some hours on it. It was running fine and then it all of a sudden had multiple cylinder misfires and a cam out of sync with crank code. Changed all the plugs and coils and put a new cam position sensor in. Cam...
  4. R

    MMX Cam Swap - Tune Question

    Hi guys. I'm finished with my Cam swap after some lifter failure / cam failure on my 2013 Ram 1500 5.7 Hemi, and got everything back together. Ready to fire it up this weekend to test everything, but took a pause on the tuner side of things. I *think* i may have made a mistake with my order from...
  5. D

    Phaser limiter orientation

    Putting a cam in my 2011 5.7, and I have a BTR phaser limiter, and one side is tapered, does anybody know if the orientation of this matters if the thinner side goes top or facing bottom? Limiter: https://briantooleyracing.com/btr-vvt-phaser-limiters.html
  6. jlyalls

    2012 Ram 1500 5.7L Hemi Camshaft/Crankshaft Sensor Repair Advice

    Good morning everyone, I hope you all are doing well. I wanted to see if I could get some advice for tackling this error I keep getting with the timing on the 5.7Hemi. Here are the things I have replaced so far. Year: 2012 Model: Outdoorsman Truck Mileage: 156,000 Crankshaft Sensor: Replaced...
    • jlyalls
    • Thread
    • 2012 ram hemi cam phaser camshaft hemi 5.7 p0016 repair tensioner timing chain.
    • Replies: 6
    • Forum: Engine & Performance
  7. H

    Please help 12’ 5.7 Hemi Cam Upgrade Lifter Change P1072 error

    2012 Ram 1500 5.7 Hemi 110,000 miles lifter stuck cam worn, replaced with AMS Racing NON MDS lifter and Comp Cam camshaft kit with Superchip tuner. Block removed, milled and cleaned brand new, compression is perfect, everything has been tested new fuel injectors gaskets are sealed. Will not hold...
  8. F

    New wire harness destroyed my engine.

    To start I have a 2013 Ram 1500 (3.6) I was getting a bad misfire on cylinders 3rd & 5th. I went ahead and replaced the ignition coil for all 6 cylinders as well as the spark plugs. The misfires continued and it was determined that the problem was the wiring harness. I took it to a Dodge...
  9. T

    2015 Ram V6 Pentastar Engine problems...eventually resolved...maybe

    I hope this information helps others with similar problems! I am an owner of a 2015 Ram 1500 Big Horn pickup with a V6 Pentastar engine. I purchased it new and now have about 109,000 miles when I started to experience engine problems. I put approximately 150 highway miles per day and I...

Latest posts

Staff online

Members online

... and 9 more.
Total: 4,103 (members: 59, guests: 4,044)
Robots: 1,313

Forum statistics

Threads
210,831
Posts
3,058,641
Members
170,683
Latest member
wcs531
Back
Top