pajeepman
Senior Member
Just turned 101,*** miles
5.9 magnum automatic
Bright red with 4 doors
Laramie so its pretty much fully loaded. Only options it did not have that I know of are heated seats, sunroof, and 20" rims.
Has power leather seats, steering wheel audio controls(Infinity sound system), power adjustable pedals, homelink, storage compartments all over, fold flat rear floor, bed liner, tinted windows, factory tow package, stainless steel nerf bars, auto dim rear view mirror, skid plates, sliding rear window, heated side view mirrors, overhead console, fog lights, electronically shifted transfer case.
At 86,000 miles it had new rotors and pads front and rear.
Summer 2016 it had new rear monroe shocks with coil overs
September 2016 it had an aluminum intake plenum installed, new cap, rotor, plugs, wires, O2 sensors, rear driveshaft u-joints(Moogs) installed.
In June 2017 in had new: 2 Moog lower ball joints, 2 new Moog upper control arms with ball joints, bilstein front shocks, tranny cooler (which is huge), steering rack and tie rod ends all replaced and a front end alignment.
Front left axle was replaced with a unit from Napa before I bought it in December 2016
265/75-17 load range E goodyear tires with lots of tread
Has rust around rear wheel wells, back bumper is banged up (before I got it in December 2015 with 85,000 Miles, front bumper has a scuff on passenger corner. NO rust on front fenders or cab, rocker and floors are beautiful. Plenum gaskwt nweds replacing again. I paid a shop to do it and it did not last for unknown reason.
Interior is beautiful, no rips in seats, not smoked in. Seats are 2 tone leather/suede. Its a dark grey color.
its in Norristown, Pa 19403 outside of Philadelphia.
Asking $6800 which is on the low end of what KBB and NADA have for the truck in the fair shape, the worst shape they list prices for. This has a rebuilt front end, other new parts, and a 95% mint interior. It has had alot of work and money in new parts installed. I did not plan on getting rid of it which is why I had just done the front end on it with quality parts(just needed 1 ball joint).
5.9 magnum automatic
Bright red with 4 doors
Laramie so its pretty much fully loaded. Only options it did not have that I know of are heated seats, sunroof, and 20" rims.
Has power leather seats, steering wheel audio controls(Infinity sound system), power adjustable pedals, homelink, storage compartments all over, fold flat rear floor, bed liner, tinted windows, factory tow package, stainless steel nerf bars, auto dim rear view mirror, skid plates, sliding rear window, heated side view mirrors, overhead console, fog lights, electronically shifted transfer case.
At 86,000 miles it had new rotors and pads front and rear.
Summer 2016 it had new rear monroe shocks with coil overs
September 2016 it had an aluminum intake plenum installed, new cap, rotor, plugs, wires, O2 sensors, rear driveshaft u-joints(Moogs) installed.
In June 2017 in had new: 2 Moog lower ball joints, 2 new Moog upper control arms with ball joints, bilstein front shocks, tranny cooler (which is huge), steering rack and tie rod ends all replaced and a front end alignment.
Front left axle was replaced with a unit from Napa before I bought it in December 2016
265/75-17 load range E goodyear tires with lots of tread
Has rust around rear wheel wells, back bumper is banged up (before I got it in December 2015 with 85,000 Miles, front bumper has a scuff on passenger corner. NO rust on front fenders or cab, rocker and floors are beautiful. Plenum gaskwt nweds replacing again. I paid a shop to do it and it did not last for unknown reason.
Interior is beautiful, no rips in seats, not smoked in. Seats are 2 tone leather/suede. Its a dark grey color.
its in Norristown, Pa 19403 outside of Philadelphia.
Asking $6800 which is on the low end of what KBB and NADA have for the truck in the fair shape, the worst shape they list prices for. This has a rebuilt front end, other new parts, and a 95% mint interior. It has had alot of work and money in new parts installed. I did not plan on getting rid of it which is why I had just done the front end on it with quality parts(just needed 1 ball joint).
