Search results
-
Stock Rim Downsize OE 20" to 17" 2013 Ram 1500
Sidewalls do a lot of work. I have never liked the trend of overly large wheels and tiny sidewalls. On a performance sports car, sure, but a truck needs to be a truck. -
Deciding on new nerf bars
Total bad ass! Those look even better than I thought they would. Can't wait to see the pictures after you install those! -
Shoulda bought this F150 instead?
Needs a Hello Kitty themed interior to really pull it off.- 3M-TA3
- Post #5
- Forum: Photos & Videos
-
What DON'T you like about your RAM?
Thoroughly pleased with one exception - the rear seat in a quad cab should fold down without having to mod it. I didn't expect that a quad cab would have less storage for things like a spare coat, tarp, snow brush, etc., than a standard cab.- 3M-TA3
- Post #1,416
- Forum: General Discussions
-
Cabin Filter - Worth It? Why?
You can also find them on Amazon and eBay - just search for 2015 ram 1500 cabin air kit (or other vehicle) -
Deciding on new nerf bars
Check out Truck Gear by Line-X. Lifetime warranty and uses factory mounting points. They come in Chrome (I have the 5" oval straight) but can be Line-X'd like the photo below. -
Head unit / camera instsll
Swap the camera inputs at the head unit and see if the problem follows the camera or the head unit. If the head unit get the dealer to replace it. If it's the camera then troubleshoot further there. Make sure all wires have continuity - you could also use a dmm and compare between the working...- 3M-TA3
- Post #4
- Forum: 4th Gen DIY
-
Aftermarket OEM Style Bumpers
You need to get the OEM harness and either the extension harness from @M2Mods or fab an extension yourself. You also need either a light switch that supports fogs (and a dealer flash to enable it) or an accessory switch. -
Fuel pump?
An easy way to access the pump is to remove the bolts holding the bed on the driver's side, then remove the passenger side bolts halfway. Pull the driver's side tail light and pull the wires so they hang loose. Pull the gas filler screws then you can lift from the driver's side and prop up with...- 3M-TA3
- Post #9
- Forum: Engine & Performance
-
Cabin Filter - Worth It? Why?
Probably not, but you can check in just a few moments. Open your glove box, then pinch in the guides so you can remove it (if you have the string dampener on the right hand side you have to remove it as well) then remove the glove box. The cabin filter access is on the right hand side and high... -
What did you do with your 4th Gen this week?
I've had the truck just about a month and so far have done the following: Replaced the factory radio with a Kenwood Navigation unit and front and rear cameras Mounted snow tires and street tires on new chrome wheels Yesterday had Northwest Running Boards install new running boards Today I...- 3M-TA3
- Post #18,472
- Forum: General Discussions
-
Cabin Filter - Worth It? Why?
I plan on doing this mod, especially after having installed the upper glove box earlier today. The amount of dust I saw behind the dash convinced me I need one. I plan on cutting the plastic using a soldering iron with a thin temporary tip. -
Wheel sdimulators
There are some pretty effective chrome paints you might try. They are so good that I've even run across wheels that were painted instead of plated you can't tell the difference. BTW I did get PLATED wheels because it's more durable, but I don't think that would be a problem with the hubs. Just... -
Hello from Communist... CA
No need to apologize and hope you make it to your new property soon. Good folks are always welcomed by other good folks. If the State of Jefferson every happens I might wind up being your neighbor. I have to warn you, though, that Oregon has had an identity crisis and is doing everything it...- 3M-TA3
- Post #20
- Forum: Introduction
-
Howdy All From The PNW
Howdy all! Below is my 2015 5.9L 1500 Tradesman with my 1997 V10 2500 peeking behind. Bought it about a month ago w/ only 35 K miles. It came with a nice dual exhaust and has that great Hemi sound, some black ION Alloy wheels with slightly oversize mudders, and the bed with Line-X applied...- 3M-TA3
- Thread
- Replies: 5
- Forum: Introduction
-
Aftermarket OEM Style Bumpers
Thanks - I've been checking CL, eBay, and Amazon. Just had a thought though - I had running boards installed yesterday and while waiting noticed they had aftermarket bumpers on their display wall. I'm going to check with them next week to see if they can keep an eye out for me when they upgrade... -
Aftermarket OEM Style Bumpers
Thanks - lots of good information there! I'm planning on using the OEM switch w/ fogs. Also looking into the M2Mods harness to make the wiring easier. What does the VSIM module do for you here? I'll check out Rock Auto and there are a few on Amazon/eBay with some pretty good reviews as well... -
Aftermarket OEM Style Bumpers
Nice! If I was looking for a painted bumper I'd be done right here. -
Aftermarket OEM Style Bumpers
Great site & thank you! Unfortunately nothing there matches what I'm looking for. I can find bumpers all day long on eBay and Amazon and really just trying to figure out if any of the aftermarket ones are good enough to go with. -
Aftermarket OEM Style Bumpers
I'm a new owner of a 2015 Tradesman. I plan on adding fog lights and want to go the OEM style route, so that means I need a bumper with fog light cut outs. MOPAR OEM bumpers run about $600 plus shipping, but I also see a lot of aftermarket bumpers at half that price or less. Does anybody have...
