Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
I updated my radio UAQ nav that I got from infotainment to the latest version posted here 22.6? It was from a 2018 ram. I’m having a couple issues where all the temps are in Celsius and I can’t change it in the settings menu also noticed that when changing temperature using the hard buttons, it only goes to high or low can’t go up one degree. Anyone have any ideas? It’s kinda annoying now. Ugh. I thought it would fix a couple issues but now it seems
things I tried..
constantly changing settings back
Remove both batteries for 10 mins
"Should" help at their prices!Infotainment has a vendor section on this forum. https://www.ramforum.com/forums/infotainment-com.169/
Perhaps they could help with the update / HVAC issue.
Yes I do. Any thoughts on where to look?
Still don't know the actual on of the radio you got (68331xxx?)What's the actual PN of the radio you have?
Do you have AlfaOBD?
.
Still don't know the actual on of the radio you got (68331xxx?)
Did your 15 ram 2500 come with factory 8.4 and dual zone ATC? (ie Laramie or higher)?
M² Mods.
I did not swap out the HVAC module. Infotainment gave me some module to use that goes between the radio and harness.That's definitely a valid ram UAQ radio PN.
and did you swap out the HVAC module in your 15ram 2500 for the 2018 version (68366553AA module) or keep the original 68105017Ax HVAC module? (It shouldn't matter unless the original one has failed).
You may be able to set the HVAC configuration to single zone MTC and then back to the factory setting of dual zone ATC with AlfaOBD... May get it squared away.
(Recommended this to Cesar Reyes also).
RESET YOUR HVAC Configuration:
Connect with AlfaOBD and go back and set your truck (Ecu Config 3) HVAC Configuration back to: Single Zone MTC
Then disconnect AlfaOBD, Shudown the truck, let it go to sleep… and pull the 20A inline Radio fuse near the brake booster at the firewall (2 minutes) to force a radio reset.
Next… Get back in and switch the truck to “run” without starting. Wait for UAQ to reset… it’s done when the SXM button appears and the Backup Camera works again.
Check the HVAC on screen menu… it should show the Single Zone temp slider without the temp readout .
Set Dual Zone ATC:
Connect back up with AlfaOBD, HVAC Configuration back to: DUAL ZONE ATC
Then disconnect AlfaOBD, Shudown the truck, let it go to sleep… and pull the 20A inline Radio fuse near the brake booster at the firewall (2 minutes) to force a radio reset. (yes again)
Next… Get back in and switch the truck to “run” without starting. Wait for UAQ to reset… it’s done when the SXM button appears and the Backup Camera works again.
Check the HVAC on screen menu… it should show both Dual Zone ATC Temp sliders with the temp readouts. (now your back to original config).
If that doesn't get it, you can try a new 2018 2500 module, swap back in the original RAx radio, etc and just have to try more detailed steps to isolate the problem.
M² Mods.
They likely included the 4c Seat interface module/T-harness to make the seats work correctly with the UAQ/UAS radio menus. (Which I forgot about).. .I did not swap out the HVAC module. Infotainment gave me some module to use that goes between the radio and harness.
I'll try this procedure at some point when its not so wet outside by me.
That's definitely a valid ram UAQ radio PN.
and did you swap out the HVAC module in your 15ram 2500 for the 2018 version (68366553AA module) or keep the original 68105017Ax HVAC module? (It shouldn't matter unless the original one has failed).
You may be able to set the HVAC configuration to single zone MTC and then back to the factory setting of dual zone ATC with AlfaOBD... May get it squared away.
(Recommended this to Cesar Reyes also).
RESET YOUR HVAC Configuration:
Connect with AlfaOBD and go back and set your truck (Ecu Config 3) HVAC Configuration back to: Single Zone MTC
Then disconnect AlfaOBD, Shudown the truck, let it go to sleep… and pull the 20A inline Radio fuse near the brake booster at the firewall (2 minutes) to force a radio reset.
Next… Get back in and switch the truck to “run” without starting. Wait for UAQ to reset… it’s done when the SXM button appears and the Backup Camera works again.
Check the HVAC on screen menu… it should show the Single Zone temp slider without the temp readout .
Set Dual Zone ATC:
Connect back up with AlfaOBD, HVAC Configuration back to: DUAL ZONE ATC
Then disconnect AlfaOBD, Shudown the truck, let it go to sleep… and pull the 20A inline Radio fuse near the brake booster at the firewall (2 minutes) to force a radio reset. (yes again)
Next… Get back in and switch the truck to “run” without starting. Wait for UAQ to reset… it’s done when the SXM button appears and the Backup Camera works again.
Check the HVAC on screen menu… it should show both Dual Zone ATC Temp sliders with the temp readouts. (now your back to original config).
If that doesn't get it, you can try a new 2018 2500 module, swap back in the original RAx radio, etc and just have to try more detailed steps to isolate the problem.
M² Mods.
Try a soft reset by pushing the volume and browse buttons simultaneously for around five or ten seconds until the radio reboots. You can also try disconnecting the battery waiting 15 or 20 minutes and see if it helps.Hi. I've been going through the 100+ pages on this thread. Thank you for all the things you've done. I have an issue with my radio. I have a 2013 1500 Big Horn 8.4 touchscreen, no Nav. It was working fine, then it one day it just got stuck on the ram logo screen. The backup camera still works, but it just stays on the logo screen or blank otherwise. I tried downloading the uconnect update, the most recent was 18.XX. When I plug the USB drive in, it does nothing. Any suggestions? Thanks again.
Do you have something plugged into the AUX port? If so remove it and see what happens.Been through all that bs 100 times.
Hi. I've been going through the 100+ pages on this thread. Thank you for all the things you've done. I have an issue with my radio. I have a 2013 1500 Big Horn 8.4 touchscreen, no Nav. It was working fine, then it one day it just got stuck on the ram logo screen. The backup camera still works, but it just stays on the logo screen or blank otherwise. I tried downloading the uconnect update, the most recent was 18.XX. When I plug the USB drive in, it does nothing. Any suggestions? Thanks again.