Recent content by tzr916

  1. tzr916

    Represent! Silver Rams - Post some pics!

    Most recent photo, latest addition being Magnum RT wheel-2-wheel steps.
  2. tzr916

    Which are the most comfortable/adjustable seats possible?

    Found a power driver seat on eBay, color and fabric matched to what's already in my truck. All hooked up and working, so far it's quite a bit better than manual, especially the adjustable lumbar.
  3. tzr916

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Thank you... Before I start pulling new wires and tearing out the old seat - I am comparing the connectors under the powered seat with the connectors under the original seat. I notice that the powered seat has an extra gray plug with one black wire, that my original seat does not have. What is...
  4. tzr916

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    I will be replacing my front driver manual seat with a powered seat (no heat, no cooling, no memory). The connector under the seat on my SLT apparently does NOT have the 12v power that is needed. What is the recommended gauge wire if I want to run the power from the battery to the connector...
  5. tzr916

    Which are the most comfortable/adjustable seats possible?

    Is this considered "10 way" adjustable? -raise -lower -forward -back -tilt seat up -tilt seat down -recline forward -recline backward -lumbar in -lumbar out
  6. tzr916

    Which are the most comfortable/adjustable seats possible?

    In case I need to match the color/fabric, are the rear seats of a QC the same as rear seats from a CC? or MC?
  7. tzr916

    Which are the most comfortable/adjustable seats possible?

    I have a 2014 SLT QC with manually adjustable cloth gray seats. In short, they SUCK. It's not that they are worn out or torn or anything. I just cannot get the correct position/support. I've tried adding foam lumbar support, and even mounting spacers attempting to raise/tilt them. I'm at the...
  8. tzr916

    Reduced turning radius after changing from 2.5" level to 4" Lift

    Mystery solved by taking an angle grinder to the back side of the new lift spindles. Was easily able to get 45 degrees more rotation on the steering wheel in each direction! BEFORE: AFTER:
  9. tzr916

    RAM 1500 visits City Murals

    https://goo.gl/maps/G9oy1vgQFQ5vb4NY6
  10. tzr916

    Reduced turning radius after changing from 2.5" level to 4" Lift

    Hmm I don't notice it being "very sloppy". I like the ride much better than just front level springs. After a few weeks I'm almost adjusted to making a bit wider u-turns and navigating parking lots.
  11. tzr916

    RAM 1500 visits City Murals

    Some new pics with my most recent mods: -changed from front level to 4" lift -oem fender flares -hellwig rear sway bar
  12. tzr916

    Reduced turning radius after changing from 2.5" level to 4" Lift

    ** SOLVED ** 2014 RAM1500 2WD I installed RC 2.5" level (springs) almost a year ago. Everything was normal except a rough/stiff front end and some bump steer on uneven roads. A few days ago, I had a local shop install RC 4" lift (stock springs, front spindles, rear spacers, 4 new shocks). I...
  13. tzr916

    Mirror tilt in reverse

    I installed full power mirrors (chrome cap "limited"), plus door modules and switch.. Programmed with alfaobd, and they work great (when paired with a back up camera). If you don't have a backup camera, I could understand how it wouldn't be a good feature.
  14. tzr916

    DIY: 2013-2016 (some 17-18) RearView Mirror Upgrade & Harness install

    Thanks for clearing up where pins 29/30 are in relation to other pins, except why are the numbers in your diagram flipped upside down from the diagram from connectors.dcctools.com? And, do you think I am risking damaging the microphone port on my aftermarket radio by feeding the oem mirror...
  15. tzr916

    DIY: 2013-2016 (some 17-18) RearView Mirror Upgrade & Harness install

    So if I want my side mirrors to dim, I could get the 911/Assist AutoDim rear view mirror 68096091AF + covers. Would I need a different wiring harness? Wow, love that link! Says pins 29 and 30 are for the microphone. The diagram points out pin 31-40. But is pin 30 directly "below" pin 40, or is...
See more

Latest posts

Staff online

Members online

... and 11 more.
Total: 1,393 (members: 61, guests: 1,332)
Robots: 1,936

Forum statistics

Threads
195,638
Posts
2,872,815
Members
156,469
Latest member
amadhi89

Share this page

Top