1000HP Hemi Ram

[Elevated 2013]

I believe the word i'm looking for is DAAAAAMMMNN! LOL. Nice truck and job on the engine and tuning. Wish I had that kind of money to put into my truck.

 

[Wild one]

Ill be racing this truck in full street trim, aside from the rear drag radials. Looking to see low 10's at 135ish mph.

Well the week-end has passed how did it run Matt.

 

[Hemi450hp]

Well the week-end has passed how did it run Matt.

The race event is this coming weekend. Private rental to try to dial it in will be on Friday, and then the MSHS race is Saturday.

I'm honestly more focused on getting Sean's truck dialed in than my own, but I'm still hoping to put down a low 10 second pass. Very nervous about whether the 9.25" will hold up though. Last time I went wide open at the track with traction, it sheared the pinion in half. We have added 200hp since then, so I dont know what's going to happen.

 

[Wild one]

The race event is this coming weekend. Private rental to try to dial it in will be on Friday, and then the MSHS race is Saturday.

I'm honestly more focused on getting Sean's truck dialed in than my own, but I'm still hoping to put down a low 10 second pass. Very nervous about whether the 9.25" will hold up though. Last time I went wide open at the track with traction, it sheared the pinion in half. We have added 200hp since then, so I dont know what's going to happen.

LOL I believe you,i think you're probably well past what the stock ZF will take reliably.I'm guessing after the first time you went to dual drive shaft loops,lol. Hopefully she holds and you get 1 real good pass out of it.What are you expecting out of Seans truck?

 

[McBroom]

Matt if you break it I’ll haul it home for you.
I pray it don’t break.


The Blue Mule

 

[Hemi450hp]

LOL I believe you,i think you're probably well past what the stock ZF will take reliably.I'm guessing after the first time you went to dual drive shaft loops,lol. Hopefully she holds and you get 1 real good pass out of it.What are you expecting out of Seans truck?

I took Sean's truck out on Friday, and only got to make 1 pass as it started raining before we got through the traps. It went 11.95 @ 111.5mph with a weak 1.76 60'. Its supposed to be 90* all weekend, but I think it will still run 11.80's in the heat. Shooting to put his truck in the 11.5's this winter in good air...still on a stock bottom end N/A 5.7.

 

[Torque]

I say you need to contact fastest cars of Netflix and stomp a hole in a supercars a**

I was thinking the same thing.

 

[Daveski]

Ohhh so so so vewy nice! Thank you for the feedback and photos!

 

[Lucy Girl]

We decided to take the shop truck a step further, and finally hit the 1000hp mark yesterday. Truck is a 2014 1500 with a MMX 422", MMX Ported BGE Heads, LOOMMX 95MM Ported Hellcat Throttle Body, Whipple 2.9L Supercharger at just over 15psi boost, ARH 1 7/8" Longtube headers w/o cats and Dual 3" Exhaust, Dual Fore fuel pumps, ID1050X Injectors, and on E85. Will be taking it down the track next weekend, so hopefully the rear axle holds up this time. View attachment 181377 View attachment 181378 View attachment 181379

We decided to take the shop truck a step further, and finally hit the 1000hp mark yesterday. Truck is a 2014 1500 with a MMX 422", MMX Ported BGE Heads, MMX 95MM Ported Hellcat Throttle Body, Whipple 2.9L Supercharger at just over 15psi boost, ARH 1 7/8" Longtube headers w/o cats and Dual 3" Exhaust, Dual Fore fuel pumps, ID1050X Injectors, and on E85. Will be taking it down the track next weekend, so hopefully the rear axle holds up this time. View attachment 181377 View attachment 181378 View attachment 181379

One Bitchen Ram.

 

[slag009]

That is one sick ride!

Sent from my SM-G960U using Tapatalk

 

[Tray Burge]

****! ****! ****! DAMN!

 

[LoneStarSilver]

We decided to take the shop truck a step further, and finally hit the 1000hp mark yesterday. Truck is a 2014 1500 with a MMX 422", MMX Ported BGE Heads, MMX 95MM Ported Hellcat Throttle Body, Whipple 2.9L Supercharger at just over 15psi boost, ARH 1 7/8" Longtube headers w/o cats and Dual 3" Exhaust, Dual Fore fuel pumps, ID1050X Injectors, and on E85. Will be taking it down the track next weekend, so hopefully the rear axle holds up this time. View attachment 181377 View attachment 181378 View attachment 181379

Matt,

Are you and that truck going to be at the Lone Star Mopar Fest this weekend??

 

[Hemi450hp]

Matt,

Are you and that truck going to be at the Lone Star Mopar Fest this weekend??

Yes sir. Will be making my first passes on this new setup at the event this weekend.

 

[LoneStarSilver]

Yes sir. Will be making my first passes on this new setup at the event this weekend.

Looking forward to seeing it and you!!

 

[tomb]

lets see a video of 1000hp RAM -I dont want to hear about it-I want to hear it!!!

 

[Sloverado]

Congrats that always been a favorite truck to see

 

[mopareg]

Looks great , keep us posted...……………...

 

[ScLeCo]

How'd you get the ARS tensioner to work on the truck? They told me it wouldn't fit because of a clearance issue.

 

[RedSRT4Me]

How'd you get the ARS tensioner to work on the truck? They told me it wouldn't fit because of a clearance issue.

I'd guess AC line relocation needs to happen to make room

 

[Hemi450hp]

ARS tensioner bolted right up. I didnt have to modify anything.