Headlight aiming help

[blackout11]

I have a question got projectors and some how the dealer screwed them up replacing my fog light using a wall how far should i be back and how high should the lows be now mind you they are projectors so they have a cut off please any and all help thanks

 

[quietpeen]

I moved this to the exterior section

If I remember correctly jj said at 20 feet your lights should have 2" drop

 

[OutlawTrucker]

As long as the cutoff is below car mirrors your golden.

 

[swamp_life hemi 05]

Wat if your truck is way up in the air

Sent from my ADR6350

 

[0212353]

I moved this to the exterior section

If I remember correctly jj said at 20 feet your lights should have 2" drop

25 ft.

As long as the cutoff is below car mirrors your golden.

thats kinda broad. Mine are way above a Vette's mirrors, but way below a donk'ed up Impala's

Wat if your truck is way up in the air

Sent from my ADR6350

 

[Graygoose]

so to clarify, 25' back away from the wall/door, the headlights should have a 2" drop from where they woudl be if you were nose up against the wall?

 

[0212353]

yup!

Call me crazy, when I do it.............I walk up to the light and put a line of tape on my jeans where the cutoff is. I walk over to the wall and bam - check. lower if need, etc.

 

[Graygoose]

sweet, need to double check mine

 

[blackout11]

And what if one light is like 2 foot above the other lol stupid fing dealership / and joy headlights have to be removed to access the adjustment screws stupid ****

 

[0212353]

why do they need adjusted? dealer jacked them up? pull them, put 'em back. shouldn't have to move 'em?

 

[OutlawTrucker]

Why you take it to the dealer anyway Walt?

 

[blackout11]

why do they need adjusted? dealer jacked them up? pull them, put 'em back. shouldn't have to move 'em?

No clue still trying to figure this out lol prob dropped it or just being smart asses cause they had to remove all the led/halo/hid wiring im surprised all my lights still even work

 

[blackout11]

Why you take it to the dealer anyway Walt?

Wellllllll i had a led tail light go out then the whole left side of my truck went out i took every light out unhooked checked yadda yadda finally found the prob the left side resister for my tail went bad and caused my truck to kick it as being faulty. So in process of this i must of left my hid fog light bulb loose went for a ride and the bulb burnt my fog light housing almost in half. So put stock **** back in my fogs and went to dealer to get new fog light installed (warranty) . And since the whole front end has to come off to get to fogs i was not messing with that lol

 

[Catchin Zs]

And what if one light is like 2 foot above the other lol stupid fing dealership / and joy headlights have to be removed to access the adjustment screws stupid ****

Same thing happened to me!!

Sent from my DROID3 using Tapatalk 2

 

[Catchin Zs]

By the way, what do you use to unscrew them?

Sent from my DROID3 using Tapatalk 2

 

[Graygoose]

20T or 7mm to adjust headlights, just adjusted mine in about 2 minutes.

 

[blackout11]

20T or 7mm to adjust headlights, just adjusted mine in about 2 minutes.

Not with mine they are aftermarket they have to be removed adjusted put back in looked at rinse and repeat

 

[Graygoose]

Ouch!

 

[0212353]

Not with mine they are aftermarket they have to be removed adjusted put back in looked at rinse and repeat

his are aftermarket too. LOL

 

[Graygoose]

haha, true