Lowered 4th Gen Pics - Show Em Off!

[Sillygoose]

love it

 

[gunner1374]

Bagged and dropped...nice!

 

[JLud]

Love the rides. Here is mine as I picked it up.

Here is mine when I picked it up before the GF 2/3.

 

[JLud]

GF 2/3 installed

Pulled the GF 2/3 kit out of my '12 ccsb when I sold it for my '13 ccsb. Then pulled it out of the '13 when I traded it for this '15. After seeing all these awesome rides on here makes me want to go lower.

 

[Kotta390]

I bought the truck like this. Factory 33" tires and from what I can tell it looks like a 2" rear drop but can't really tell if the front has been dropped?

 

[sicmadek]

I bought the truck like this. Factory 33" tires and from what I can tell it looks like a 2" rear drop but can't really tell if the front has been dropped?

The front looks dropped also

 

[Kotta390]

The front looks dropped also

I was sorta thing the same but I would need to see what a RC hemi truck looks like stock

 

[CMil527]

Pulled the GF 2/3 kit out of my '12 ccsb when I sold it for my '13 ccsb. Then pulled it out of the '13 when I traded it for this '15. After seeing all these awesome rides on here makes me want to go lower.

looks great!

 

[R/T_Fire]

Finally washed it...

What Kit do you have on yours and tire size?

I run the 285/45r22's and looks like I sit lower than yours... I'm trying to figure out the kit and or what was done to mine

 

[PassivAggressor]

I was sorta thing the same but I would need to see what a RC hemi truck looks like stock

Stock

 

[PassivAggressor]

What Kit do you have on yours and tire size?

I run the 285/45r22's and looks like I sit lower than yours... I'm trying to figure out the kit and or what was done to mine

You probably have a cut Belltech kit.

 

[R/T_Fire]

You probably have a cut Belltech kit.

would explain the excessive inner fender contact I get. just wouldn't think a major dealer would sell a truck with a bastardized lowering kit... but I'm not complaining cause I love its stance.. just needs to drop about 3/8"-1/2" in the rear

 

[PassivAggressor]

would explain the excessive inner fender contact I get. just wouldn't think a major dealer would sell a truck with a bastardized lowering kit... but I'm not complaining cause I love its stance.. just needs to drop about 3/8"-1/2" in the rear

I highly doubt they knew it was cut (if it is). Just because its cut doesn't mean it's bastardized though. A lot of guys do it.

 

[R/T_Fire]

I highly doubt they knew it was cut (if it is). Just because its cut doesn't mean it's bastardized though. A lot of guys do it.

Its a liability thing. most modified or custom stuff dealers send to whole sellers. but it was also sold as a as-is no warranty but I still got a warranty work with the engine. sneaky sneaky

Whom ever installed the kit did a great job and it was installed right... I think the swaybar endlinks were taken off by a employee and stockers put in their place. just a feeling cause the rest of the truck you can tell had money spent on it to do it right except for that.

 

[DERJ]

What Kit do you have on yours and tire size?

I run the 285/45r22's and looks like I sit lower than yours... I'm trying to figure out the kit and or what was done to mine

I'm running the Belltech 2/4 kit (springs and shocks) with factory 285/45 R22s.

I'm parked on a slight incline so the front looks higher - on level ground, mine sits 1/8" lower up front - Here's a side pic on level ground:

 

[Joe-13]

Stock
I want a 3/5 drop. how can i get that?

 

[Blackbeast]

3/5 drop

How did you get that 3/5 drop? What did you use and what mods did you have to do to achieve it?

 

[Blackbeast]

How did you get that 3/5 drop?.. What did you use and what mods did you do to achieve it?

 

[gunner1374]

Buy a 2/4 and cut it down. That's what I am planning to do after I get my new 55 or 50 series 20 inch tires on. I am going to a shorter tire as well for small weight savings and mostly to help with effective gearing. I have 392s and want a little more acceleration help without the expense of going to a 4.56 gear.

 

[R/T_Fire]

I'm running the Belltech 2/4 kit (springs and shocks) with factory 285/45 R22s.

I'm parked on a slight incline so the front looks higher - on level ground, mine sits 1/8" lower up front - Here's a side pic on level ground:

First truck I've seen with the same stance as mine... the back needs to come down to level. It bugs the hell outa me... do you get any inner fender contact?

Sent from my SM-G920V using Tapatalk