Inez Hotrods 4/6 Drop

TylerB · Apr 6, 2017

Looks great man!

Somebody needs to buy my McGaughy's spindles and coils so I can get this kit, I've got the rear coils covered so I wonder if they'll knock done off the price since I don't the $200 Belltech rear kit.

TylerB · Apr 6, 2017

And I'm assuming there's still plenty of adjustment left in the front to go down to 5"?

PassivAggressor · Apr 6, 2017

TylerB said:
Looks great man!

Somebody needs to buy my McGaughy's spindles and coils so I can get this kit, I've got the rear coils covered so I wonder if they'll knock done off the price since I don't the $200 Belltech rear kit.

I'm somebody! Sent a PM.

Quicksilver337 · Apr 6, 2017

TylerB said:
Looks great man!

Somebody needs to buy my McGaughy's spindles and coils so I can get this kit, I've got the rear coils covered so I wonder if they'll knock done off the price since I don't the $200 Belltech rear kit.

yes they will... I also have the rear Belltech springs. So all I needed was the front arms and rear bracket :favorites13:

R/T_Fire · Apr 6, 2017

I need to figure out what I need to do and get.... since I'm already sitting so low on a modified belltech kit....

I'm thinking of starting off with the Inez kit, and going from there. I may get a set of McGaughys drop spindles, mill the outside to keep the wheel flush and then decide what spring to get. most likely a 1" or stock height "performance" spring from Crown.

I'll prob decide all this when I pull it in the shop to do the fuel tank and rear susp modifications. I need to also compare the cost and benefit to a parallel 4 link vs using Inez relocation set up for the rear.

also has anyone talked to them about a coil over set up?

Quicksilver337 · Apr 7, 2017

TylerB said:
And I'm assuming there's still plenty of adjustment left in the front to go down to 5"?

Inez told me that you can get the 4" or 5" drop arms but they recommend the 4". If you want to go lower in the future I guess a 1" drop spring from Crown would do the job.
I wonder if my QA1 front shocks will still work for the Inez setup

ramittome · Apr 7, 2017

That's what I was asking earlier and was told yeah because it uses a shorter spring, then was told reuses stock spring... I don't know who to believe anymore. Lol!

Quicksilver337 · Apr 7, 2017

ramittome said:
That's what I was asking earlier and was told yeah because it uses a shorter spring, then was told reuses stock spring... I don't know who to believe anymore. Lol!

Inez sells a 4" drop arm or a 5" drop arm, for both arms you use the stock springs and shocks.
I was stating in my other post that if you get 4" drop arm and want to go lower then either cut the stock spring or use the 1" lowering spring from Crown suspension.

ramittome · Apr 7, 2017

Yeah, I get that much. I was agreeing with you on the QA1 shock. Lol! Wondering if the TS514 would work for the front since it's a shorter shock for the spring drop and with this kit you reusing the OEM springs.

Quicksilver337 · Apr 9, 2017

Since the front will have the factory suspension geometry I don't think the QA1 shocks would work. maybe with a shock extension. I would have to look into that.
I read that the factory front shocks on my R/T are good quality.

Quicksilver337 · Apr 10, 2017

Well just found out with QA1 that the TS514 will work with the stock spring setup. Only thing that needs to be done is add a 1" extension per shock... QA1 p/n: 9029-163

predat-r · Apr 12, 2017

So got a question for u guys bought the Belltech suspension 2/4 drop go to have it installed can't. I have a 4x4 model that has a different front assembly. So before I return is it possible at all to make this work?

Sent from my SM-N920P using Tapatalk

charonblk07 · Apr 12, 2017

predat-r said:
So got a question for u guys bought the Belltech suspension 2/4 drop go to have it installed can't. I have a 4x4 model that has a different front assembly. So before I return is it possible at all to make this work?

Sent from my SM-N920P using Tapatalk

The rear will work just fine but you need either drop spindles or the Ground Force drop springs. Those are your only options for the 4wd.

ramittome · Apr 12, 2017

Seeing as you have a 4x4, I highly doubt you can make any of this work. Your suspension is completely different from ours up front. Only things that are the same are the upper control arms. The kits belltechs sells are for RWD trucks only.

predat-r · Apr 12, 2017

ramittome said:
Seeing as you have a 4x4, I highly doubt you can make any of this work. Your suspension is completely different from ours up front. Only things that are the same are the upper control arms. The kits belltechs sells are for RWD trucks only.

Thats what i was told after, the tech originally said it worked. Then when I called again he said he miss spoke and hope I called back to clear it up. Yes the front set up is def different as already stated but can I use lowering springs with oem shocks to get desired drop.

Sent from my SM-N920P using Tapatalk

predat-r · Apr 14, 2017

charonblk07 said:
The rear will work just fine but you need either drop spindles or the Ground Force drop springs. Those are your only options for the 4wd.

Have anyone tried this?
Waiting on a call back from groundforce there kits is 4wd.

Sent from my SM-N920P using Tapatalk

charonblk07 · Apr 14, 2017

predat-r said:
Have anyone tried this?
Waiting on a call back from groundforce there kits is 4wd.

Sent from my SM-N920P using Tapatalk

That's their 4wd kit, I'm running the front springs from that kit in my quad cab.

Quicksilver337 · Apr 14, 2017

there is a discussion about lowered 4x4 http://www.ramforum.com/f39/strictly_4x4_lowering_thread-12208/

predat-r · Apr 14, 2017

Thanks.........

Sent from my SM-N920P using Tapatalk

R/T_Fire · Apr 18, 2017

For those with questions and that have facebook follow the link.
this just popped up on my FB feed today

https://www.facebook.com/inezhotrodzcustomz/videos/1294338717321950/

also its mentioned on the Video that Moes Performance will be a place to purchase them, but I checked Matt's wedstire and not yet listed... I know he is swamped but hopefully he will have his site updated soon and them listed with price and a easy way for those interested in this kit having a point and click way to order soon.

Once things settle down I'll be ordering a kit but I need new springs and such since my belltech's are already modified to a 3/5 - 4/6 range, hopefully I can find a local guy who wants my kit and swap it out....

Inez Hotrods 4/6 Drop

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Similar threads

Forum statistics

Share this page