Zone body lift instructions. Just ordered a kit

[Puba08]

Thanks! I’ll download those ones too!


That sounds like a rust issue for sure IMO! Maybe the body lift will help with trapped water between the body and the frame?

Is that the blocks that support the bed? The ones held in place with the push pin?


Sent from my iPhone using Tapatalk

Yes. Its hard to get your hand up in there to feel for the rubber things you have to remove. In hindsight, If I had some mirrors it may have been easier.



Sent from my iPhone using Tapatalk Pro

 

[Addicted2fishing]

Yes. Its hard to get your hand up in there to feel for the rubber things you have to remove. In hindsight, If I had some mirrors it may have been easier.



Sent from my iPhone using Tapatalk Pro

So it’s just a flat rubber plug on top of the frame? Any bolts that for though them ?


Sent from my iPhone using Tapatalk

 

[shadowhawk]

So it’s just a flat rubber plug on top of the frame? Any bolts that for though them ?


Sent from my iPhone using Tapatalk

You'll know it when you see it

 

[Puba08]

Yea you remove the rubber piece in the frame, install the crush block, then put the rubber piece back in the middle of the crush block to hold it in place. (If that makes sense)


Sent from my iPhone using Tapatalk Pro

 

[Addicted2fishing]

Thanks guys. What the heck are these and why doesn’t zone mention these ?


Sent from my iPhone using Tapatalk

 

[Puba08]

Which pic, the 3rd?


Sent from my iPhone using Tapatalk Pro

 

[Addicted2fishing]

Which pic, the 3rd?


Sent from my iPhone using Tapatalk Pro

First and second. We don’t have to remove with the zone kit right ?

Also, while I’m here. What the heck do I do with that step spacer on the rear bumper ? How does it stay secure ? My particular hitch doesn’t have a bolt from the top down in the middle. It’s just the two centre ones


Sent from my iPhone using Tapatalk

 

[Addicted2fishing]

Lift came a day early !


Sent from my iPhone using Tapatalk

 

[Puba08]

First and second. We don’t have to remove with the zone kit right ?

Also, while I’m here. What the heck do I do with that step spacer on the rear bumper ? How does it stay secure ? My particular hitch doesn’t have a bolt from the top down in the middle. It’s just the two centre ones


Sent from my iPhone using Tapatalk

You take the stock body mount bolts off the truck, hammer the bolts out and replace with the longer bolts that are included in the kit. Then reinstall.


Sent from my iPhone using Tapatalk Pro

 

[Puba08]

First and second. We don’t have to remove with the zone kit right ?

Also, while I’m here. What the heck do I do with that step spacer on the rear bumper ? How does it stay secure ? My particular hitch doesn’t have a bolt from the top down in the middle. It’s just the two centre ones


Sent from my iPhone using Tapatalk

The step spacer just lays underneath the bumper IIRC?.....it’s been a while


Sent from my iPhone using Tapatalk Pro

 

[Addicted2fishing]

I got the back all done. I’m gonna do the front tomorrow. 1) I don’t have it in me and 2) I’m out of beer... first world problems


Sent from my iPhone using Tapatalk

 

[Tpearson515]

First and second. We don’t have to remove with the zone kit right ?

Also, while I’m here. What the heck do I do with that step spacer on the rear bumper ? How does it stay secure ? My particular hitch doesn’t have a bolt from the top down in the middle. It’s just the two centre ones


Sent from my iPhone using Tapatalk

Correct that's different from the zone kit, i can't quite remember thr bumper spacer but if it was complicated I would have remembered lol just sits underneath the step piece.



Sent from my SM-N975U using Tapatalk

 

[Tpearson515]

I got the back all done. I’m gonna do the front tomorrow. 1) I don’t have it in me and 2) I’m out of beer... first world problems


Sent from my iPhone using Tapatalk

Damn downed your truck with low beer supply, risky lol

Sent from my SM-N975U using Tapatalk

 

[Addicted2fishing]

Folks! In need of assistance. I’m on to the front brackets and they have a curve on them. Which way do they face? The Zone instructions are good and all but.....




Sent from my iPhone using Tapatalk

 

[shadowhawk]

takes you right to that spot in the install, but the empty space faces down to the ground

 

[Addicted2fishing]

takes you right to that spot in the install, but the empty space faces down to the ground

That part I get. But what about the curve?


Sent from my iPhone using Tapatalk

 

[shadowhawk]

oh... that curve I don't remember. It has to allow the bumper to fit over it, or flush with it.

the video show the plate being flush when you are done installing that plate, so it would have to face back into the engine bay with the curve.

 

[Addicted2fishing]

Never mind.... I’m an idiot.

I think too much. That’s my problem. My wife would disagree however


Sent from my iPhone using Tapatalk

 

[Addicted2fishing]

Why is it a job that requires like 3 tools end up lookin like this ?


Sent from my iPhone using Tapatalk

 

[shadowhawk]

just be glad you have the space to make a mess like that.