AlfaOBD

[Lawsuit11]

Is there a way to turn off the seatbelt dinging (when seatbelt is not being worn) with the alfa?

There is a setting in Alfa I used but I can’t seem to find it. I will update if I find it.


Sent from my iPhone using Tapatalk

 

[Doug Hawkins]

Hate to sound dumb, but what is "baseline" versus "highline"? I'm wanting to program one of the "teardrop" shaped fobiks, not an Enter-n-Go setup, for my 2017 1500 so my wife also has one, and I don't want to mess up the new fobik in the process.

 

[gapi]

Issues with what mods?

We also have a Charger. Its performance pages (PP). It don't make sense because I have enabled PP on several Chargers with no subscriptions. When we try and pull them up it says Please Wait, reminding me of the Bluetooth/Hands Free Module failures.

Thanks

 

[Reefer]

Easiest way is via: 1. Get in truck, close the door and the ignition switch in the off position, buckle the driver’s seat belt.

2. Turn or push the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off.

3. Within 20-30 seconds of turning the ignition switch to the ON position and seatbelt light going off, unbuckle and then re-buckle the driver’s seat belt four times within 10 seconds, ending with the seat belt buckled.

4. Turn the ignition switch to the LOCK/OFF position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.



AZJohnnyO
Sent from my iPhone using Tapatalk Pro

Thanks, I appreciate it.

 

[Lawsuit11]

We also have a Charger. Its performance pages (PP). It don't make sense because I have enabled PP on several Chargers with no subscriptions. When we try and pull them up it says Please Wait, reminding me of the Bluetooth/Hands Free Module failures.

Thanks

Have you tried to disable it let it take to the BCM and enable it again? Just a shot in the dark lol.

Sounds like when it was enabled it was running with the subscription and now the subscription is gone it can’t run with it cause it’s unavailable. So maybe re enable it with no subscription and it will configure it without it. Again. Total shot in the dark lol


Sent from my iPhone using Tapatalk

 

[Reefer]

Easiest way is via: 1. Get in truck, close the door and the ignition switch in the off position, buckle the driver’s seat belt.

2. Turn or push the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off.

3. Within 20-30 seconds of turning the ignition switch to the ON position and seatbelt light going off, unbuckle and then re-buckle the driver’s seat belt four times within 10 seconds, ending with the seat belt buckled.

4. Turn the ignition switch to the LOCK/OFF position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.



AZJohnnyO
Sent from my iPhone using Tapatalk Pro

Just tried it and glad to report that it worked. thanks!

 

[1500ram12]

Hate to sound dumb, but what is "baseline" versus "highline"? I'm wanting to program one of the "teardrop" shaped fobiks, not an Enter-n-Go setup, for my 2017 1500 so my wife also has one, and I don't want to mess up the new fobik in the process.

Highline is the push to start systems. The fobs you insert are baseline


2018 2500 6.4L Tradesman

 

[SitKneelBend]

Yes and no. There is no way to disable all controls on every door. IE lock and unlock on the passenger will still work. But you can enable the passenger door window lock with the lock button on the drivers side. Let me see if I can find it and I’ll let you know. This only enables the passenger door and back windows lock on the drivers switch. They come from the factory with the switch on enabled to lock the back windows

Edit. Option your looking for is here

Doors Configuration:
Global Up: Set
Global Down: Set
Sun Shade: Not set
Puddle Lamp Present: Set
Rear Door pre short drop behavior: Not set
**Passenger Window Lockout: Not set**


Sent from my iPhone using Tapatalk

It looks like I may not have that option in my 2014...is it under "car configuration change"?

Sent from my HTC U11 using Tapatalk

 

[Wayne Stella]

ECU config 4


Sent from my iPhone using Tapatalk

In the Body Computer/Car configuration change/ECUConfig 4-IPC Feature Configuration/ Value yes? Or is it another ECU Config 4 item?

 

[Lawsuit11]

In the Body Computer/Car configuration change/ECUConfig 4-IPC Feature Configuration/ Value yes? Or is it another ECU Config 4 item?

No that is the correct one value yes


Sent from my iPhone using Tapatalk

 

[Wayne Stella]

No that is the correct one value yes


Sent from my iPhone using Tapatalk

Thank you

 

[Lawsuit11]

It looks like I may not have that option in my 2014...is it under "car configuration change"?

Sent from my HTC U11 using Tapatalk

Here’s a screen shot of mine. It’s under car configuration change. Section is doors



Sent from my iPhone using Tapatalk

 

[Lawsuit11]

Just tried it and glad to report that it worked. thanks!

This is where it is at in Alfa it’s under the IPC(cluster). When I went from my 3.5” to my 7” I had to change the setting again because it’s stored in the cluster and not in BCM



Sent from my iPhone using Tapatalk

 

[Wayne Stella]

No that is the correct one value yes


Sent from my iPhone using Tapatalk

It worked! If my bad back would allow me to dance a jig, I'd be dancing right now. Thank you! Since putting the premium 7" evic in the dash, coupled with the Tesla Style radio I had lost all of those settings as they were in the RA2 radio. I now have the "Vehicle Settings" menu in the evic. It allows access to trailer settings, compass settings, etc., all the items in the "Console Menu" of the Tesla radio that do not work or are just not there. As you said before it should be added to the known working items if it isn't already there.

 

[Bent]

I apologize if this was asked already, I did try skimming but 786 pages is a LOT of information to sort through! I am kind of bummed that my power folding mirrors don't have a setting to fold when my truck is turned off. Is there an option in the alphaOBD that I could change that?

 

[chri5k]

I apologize if this was asked already, I did try skimming but 786 pages is a LOT of information to sort through! I am kind of bummed that my power folding mirrors don't have a setting to fold when my truck is turned off. Is there an option in the alphaOBD that I could change that?

Unfortunately there is not. It is not a function programmed into the BCM so Alpha can not set or unset it.

 

[Bent]

Unfortunately there is not. It is not a function programmed into the BCM so Alpha can not set or unset it.

well that sucks. Thanks though!

 

[SitKneelBend]

So it looks like the my 2013-2017 option I use is missing that one option. I do see it when I select my 2016-2017 (but I'm guessing that won't work on my 2014)...

Thanks for the assist though @Lawsuit11!

Sent from my HTC U11 using Tapatalk

 

[Lawsuit11]

So it looks like the my 2013-2017 option I use is missing that one option. I do see it when I select my 2016-2017 (but I'm guessing that won't work on my 2014)...

Thanks for the assist though @Lawsuit11!

Sent from my HTC U11 using Tapatalk

Try this.

Select the one that says it needs an adapter if you use OBD MX it will connect



Sent from my iPhone using Tapatalk

 

[SitKneelBend]

Must it be OBD MX? I have a cheap Bluetooth adapter...

Veepeak Mini Bluetooth OBD2 OBDII... https://www.amazon.com/dp/B011NSX27A?ref=ppx_pop_mob_ap_share

Sent from my HTC U11 using Tapatalk