Eibach Pro Lift Struts

[ram1500rsm]

That is a very nice setup considering you're running 315s on 17x9s. Being that wide didn't give you any issues? The widest that a tire shop would recommend was 285 for a 17x9 wheel. Thinking of saving some coin (for the Eibach kit) and just get wider tires for my 17x9. Good to see that it can be done.

??
Min width for a 315/70/17 tire is 8"


You can run a 37x13.5x17 tire on the same 9" wheels if you wanted

 

[Jasfish18]

First 2 pics before, second 2 after

Haven't put wheel liners back in yet, thinking bout spraying some fluid film all up in ther first...lol

 

[hodge-xj]

First 2 pics before, second 2 after

Haven't put wheel liners back in yet, thinking bout spraying some fluid film all up in ther first...lol

View attachment 215655

View attachment 215656

View attachment 215657

View attachment 215658

Looks good! What setting up front?

While you're spraying, pop the tail lights out and you can get up above the rear wheel arches nice and easy in the bedside cavity.

Sent from my SM-N920V using Tapatalk

 

[Jasfish18]

I did the lowest setting that is supposed to get 2.75 in but only got about 2in in front.
Rears I got about 1.5 in, so I really got more of a raise than a level

I did tear my boots getting ucas off, probably just go with mevs since people have luck with tham at 2 in also rc uca are for 3in lift and customer service couldnt say if they would work or not

 

[hodge-xj]

I did the lowest setting that is supposed to get 2.75 in but only got about 2in in front.
Rears I got about 1.5 in, so I really got more of a raise than a level

I did tear my boots getting ucas off, probably just go with mevs since people have luck with tham at 2 in also rc uca are for 3in lift and customer service couldnt say if they would work or not

Looks great and likely rides even better. I have the ready lift control arms through @Nick@GotExhaust he can get you awesome pricing. I ran the ready lift arms at about 2" with no issues. Don't waste the money on mevos, they do nothing for proper geometry.

Sent from my SM-N920V using Tapatalk

 

[Nick@GotExhaust]

I would recommend the Zones. the ReadyLifts are also good. Mevotechs are not much of an upgrade especially if you are lifted over stock.

 

[Jasfish18]

I would recommend the Zones. the ReadyLifts are also good. Mevotechs are not much of an upgrade especially if you are lifted over stock.

I was initially looking at rc because there almost 200 bucks cheaper than zones.
But shoot me some prices on the zones and ready lifts, that would be great!

 

[Gary2]

RC anything is cheaper than the good stuff for good reason unless their Ram parts are a lot different than Jeep parts.

 

[Jasfish18]

Here's the stock uca, true be told I don't know what a good angle is...lol

 

[RedSRT4Me]

Here's the stock uca, true be told I don't know what a good angle is...lol

View attachment 215786

That balljoint looks spot on from the pic. As long as its greases you should be good to go.

 

[Sgambots91]

I just bought some eibach front springs to pair with my Bilstein 5100. I have a 19 classic warlock which comes with 1” factory lift. I’m guessing through the coils? So I’m thinking of setting the strut on the 2nd ring. What you guys think?

 

[hodge-xj]

I just bought some eibach front springs to pair with my Bilstein 5100. I have a 19 classic warlock which comes with 1” factory lift. I’m guessing through the coils? So I’m thinking of setting the strut on the 2nd ring. What you guys think?

2nd ring should get you about 2.75 with the eibach coils.

Sent from my SM-N920V using Tapatalk

 

[GIJoe2010]

3rd will get you 3” and as far as you want before CV angles become a real issue

 

[Sgambots91]

3rd will get you 3” and as far as you want before CV angles become a real issue

Im on Mevotech UCA so probably don’t wanna go to 3” correct?

 

[GIJoe2010]

Probably not

 

[Hammer22801]

Got mine installed today. Ride quality is great but I’m going to get an alignment and my wheels rebalanced tomorrow.

so far I got about 2.5” in the front and about 1” in the rear with a total of 1.5” of rake

Once I get my wheels in and put on my truck I’ll do a thread with all the additions. You can definitely tell the trucks higher.

CV joints are damn near horizontal they are great angles.

 

[Hammer22801]

1st 2 pics pre lift last 3 post lift.

mine are on the last notch and CV angles are good. Louisiana roads suck so I’m staying on last Notch for now.

prelift
Front 36.75
Rear 40

post
Front 39 to slightly above 39
Rear 41

I also went from 275/60/20 tires to 275/65/20 tires with 20x10-24 wheels to follow soon

 

[jwhyte]

what size tires are you running?

35x11.5r20 on 20x9 +1 offset

Sent from my SM-G981U using Tapatalk

 

[Hammer22801]

Finally finished my truck for now

 

[bbaxley01]

Eibach kit installed Friday. Coils and shocks In the front. Shocks on lowest setting Spacer in the back. Got 2.5 inches in the front and 1.5 in the back.