TheSouthernOracle
Junior Member
Out of curiosity I have 2016 Ram that came from Canada and from what I've read i should be good to go with alphaodb and mx+. Just want to double check, there are few mods I've been reading up on and and want to do.
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Does anyone know what settings for diameter of a 37” tire should be programmed into the bcm? I’ve used a tire calculator and for a 37x13.5r20 says it should be set to 2951mm. The Speedo is showing we are going 60, but gps’s are saying 57ish-58. The guy wants it pretty close. We went up to 2960 and it’s still off by the same amount. I know we are talking mm here but just trying to get a good base number to get me close enough to be happy. Got the tpms stuff done just hanging in this tire circumference.
2017 Ram 2500 Laramie 37” nitto trail grapplers.
Yeah I was actually looking at measuring the tire. I figured brands played a difference in circumference. Thanks for your tips. I knew it wouldn’t match. My friend who I’m doing this for wants it to be as close as possible. I told him it would never be 100% because of tire wear etc.Go out and actually measure the tire to get closer. There is variance between brands, inflation etc so best to just get a real measurement. Then just tweak it from there. Try making larger adjustments if you need to. Don't expect it to be exactly the same as GPS every time, there is going to be a little variance depending on many factors. If you can get it within 1 on average you are doing pretty good.
.
Out of curiosity I have 2016 Ram that came from Canada and from what I've read i should be good to go with alphaodb and mx+. Just want to double check, there are few mods I've been reading up on and and want to do.
So I installed these: https://www.americantrucks.com/ram1500-smoked-led-tail-lights-03-dr13tledsm.html
Aftermarket LED taillights lights on my truck.
I had factory LED taillights stock and the new tail lights I have work fine.
I am however getting error codes saying both rear turn indicators are not working.
I checked alfaobd and everything is set to LED.
Any suggestions?
I'm guessing they don't have the DTC circuit. SET Rear Lighting DTC Disable
Ok... calling all the Alpha Omega's....lol
Question #1 ) what all needs to be enabled - and or shut off to make the door open work again?
Question #2) does the door signal have any bearing on programming fobiks?
Did you ever share the screen shot of current values of a 32 gallon fuel tank? I went from 26 to 32 and when empty it still has 6 gallon left. I have tried everything, currently I just put in the tank as a 34 gallon to help offset the gauge.mine has the 32 gal tank that is working accurately. I'm not near my truck right now won't be til Wednesday. I'll grab a screen shot when in able to.
Can you post your original BCM configuration log before you started doing everything, and then post one of your current BCM settings as they are right now?Keyless and go issues- 2014 1500 RCSB ST plain jane swap to sport Laramie.
Hey team, all parts installed - the alpha added options as listed in the bcm - try to program the fobiks and below is the screenshot of the failed message.
Amazon key fobs - chrysler new RF hub, all other parts came from a donor truck.
I think the push button works as when I press it it says -no fob detected- push brake to start, does not go to acc or run.
No idea if the fobs work or not, assuming they do.
Tried the dealer supplied SKIM CODE ( is that the correct 4 digit code to use?)see pic.. Do I need to enable skim present in bcm?
Tried the 0000 as it says on the alpha app no dice either.
Any ideas on whats not working? Can I try to add the new RF hub first?
Really trying to get this sorted before I put the interior back together and just scrap the idea for now....
Sent from my SM-N975W using Tapatalk
I dont belive I saved the logs correctly this is what I have done as that saved. I will try to figure out the full bcm log and report it back as wellView attachment BODY_CHRYSLER_Info.pdfView attachment 7 aug 20BODY_CHRYSLER_Info.pdfCan you post your original BCM configuration log before you started doing everything, and then post one of your current BCM settings as they are right now?
Damn.... i can't figure how to save the system id on my phone. Faults and changes save. Sorry ill have to do a million screen shots.Can you post your original BCM configuration log before you started doing everything, and then post one of your current BCM settings as they are right now?
Did you ever share the screen shot of current values of a 32 gallon fuel tank? I went from 26 to 32 and when empty it still has 6 gallon left. I have tried everything, currently I just put in the tank as a 34 gallon to help offset the gauge.