camshaft

  1. R

    Stage 2 Cam for a 6.4 ram 2500 with Lockout or Limter

    So I've done a bunch of searching for answers on limiters vs lockouts on the vvt. From what I gather stage 3 and lower cams generaly benifit from only limiting the vvt. Where as the lockout will actually decrease the power at lower rpm. I found that at FRP and MMX they list limiters. So when I...
  2. A

    Issues after cam swap

    Morning all, Taking to this group for some help on my cam swap I did on my 09 HEMI. Just got done replacing JUST the cam (no lifters). Re timed it by lining up the marks on the chain with the phaser at 12 o clock and pointing the keyway of the crank at 3 o clock (or towards the 5.7 mark on the...
  3. A

    Issues after cam swap

    Morning all, Taking to this group for some help on my cam swap I did on my 09 HEMI. Just got done replacing JUST the cam (no lifters). Re timed it by lining up the marks on the chain with the phaser at 12 o clock and pointing the keyway of the crank at 3 o clock (or towards the 5.7 mark on the...
  4. S

    Can swap advice

    Hey folks. I’m looking to do a cam swap. I was wondering if anyone had any good suggestions. I’m looking to get the most HP gains without losing reliability, I understand that I’ll probably have to replace springs, push rods and lifters so I don’t lose said reliability. All advice is appreciated.
  5. A

    Camshaft rod bearing Bolt Broke

    1AD99A98-059C-4D3B-8C04-2F8F59423CE8 by Arbor-D posted Apr 19, 2021 at 5:15 PM I have an 05, Ram 1500 V6 3.7l engine. I bought the owner’s manual; and found nothing mentioned of replacing the camshaft bearing cap bolts. I’ve re-torqued it once, and had to take off and do again. All of them were...
  6. jlyalls

    2012 Ram 1500 5.7L Hemi Camshaft/Crankshaft Sensor Repair Advice

    Good morning everyone, I hope you all are doing well. I wanted to see if I could get some advice for tackling this error I keep getting with the timing on the 5.7Hemi. Here are the things I have replaced so far. Year: 2012 Model: Outdoorsman Truck Mileage: 156,000 Crankshaft Sensor: Replaced...
    • jlyalls
    • Thread
    • 2012 ram hemi cam phaser camshaft hemi 5.7 p0016 repair tensioner timing chain.
    • Replies: 6
    • Forum: Engine & Performance
  7. 14Deebo

    OEM 5.7 HEMI MDS Camshaft and lifters

    Selling a stock MDS Camshaft and lifter set with trays from my 5.7 2014 Ram 1500. One of the lifters is bad, but I am not sure which one, so you'll have to check them to be sure. Cam and lifters have 53k miles on them and all appear to be in great condition (obviously other than the one bad...
    • 14Deebo
    • Thread
    • 5.7 cam 5.7 camshaft 5.7 lifters camshaft mds camshaft
    • Replies: 2
    • Forum: For Sale
  8. Kasey

    Camshaft replacement

    Hey fellas, I had to replace a camshaft now my truck wont idle, will tuning fix this issue? Its throwing a po300. The new cam is OEM. Please and thanks for the help.
  9. R

    Cam n Lifter Job

    Lifter seized up on #5 looking for a list of all applicable parts including non related parts i should be replacing while im in there, that i will need to complete this job. Here is what i have so far in my cart. - Cylinder head bolts - Head gaskets - Manifold bolts - Manifold gaskets -...
    • Roloff
    • Thread
    • 2011 cam camshaft help hydrolic lifters lifter failure lifters
    • Replies: 5
    • Forum: Engine & Performance
  10. MK96

    Search for a replacement camshaft and valve lifters

    What do you guys think about ENGINETECH or MELLING camshaft and lifters? Are these durable? Seems I might need a cam sooner or later and I won't go for performance cam in the $800 range. I would prefer non MDS cam and Hellcat non MDS lifters. Also, the camshaft bearings don't need to be changed...
  11. Will_OT

    Camshaft swap in Ottawa?

    Anybody from the Ottawa Ontario region know of a good mechanic/garage I can take my 2014 Ram to for a camshaft swap and how much it might cost? I was thinking about getting one from Moe's but it's not something I'm comfortable with doing myself.
    • Will_OT
    • Thread
    • cam camshaft swap
    • Replies: 12
    • Forum: Regional
  12. connor98

    Shift patterns

    I have a 2010 1500 5.7L sport 4x4 and I just had my camshaft replaced along with a few other parts related to a limping cylinder. Before the repair my truck would shift at around 1800rpms now 1st -2nd @ 2000rpms 2nd -3rd @2000rpms 3rd-4th @ 2500rpms and same for 4th-5th. Though while driving it...
  13. RLynnDay

    P0340 P1391 help

    P0340 P1391 help Ok guys, I need some help. I'm an experienced amateur, being the daughter of a mechanic and having worked on my own and friends/family's vehicles for almost 30 years - but this darn Dodge has me befuddled. Awhile back I had some problems with a crank/no start which ended up...
  14. R

    Truck dies at initial start

    i recently swapped a 5.9l 360 in place of my factory 5.2l I installed a comp cams “RV” cam shaft installed new coil, plugs, wires, distributer cap and rotor, crank position sensor, as well as various other sensors... I got a 5.9l ecu from a local pull apart yard as i had read on other fourms...
  15. W

    Rough and Inconsistent Idle, frequent stalling and bogging down under acceleration

    I have a 2005 Dodge Ram 1500 Hemi that I have been trying to fix for almost two years now. My brother ran it to empty one too many times and clogged up Injectors and the truck wouldn't start properly again. Had my mechanic take it apart to find the cause and found that a valve had broken off...

Latest posts

Staff online

Members online

... and 12 more.
Total: 1,455 (members: 62, guests: 1,393)
Robots: 1,886

Forum statistics

Threads
195,596
Posts
2,872,338
Members
156,402
Latest member
pierogi

Share this page

Top