Went And Made A Few Pulls

[KLRpanda]

Went and made a few pulls down the road after reseting the computer with the neg cable for about 2-3 hours

Got out of the throttle at first due to spinning
WOT bolt on 4th gen Hemi - YouTube

2nd gear pull from 20
WOT bolt on Hemi - YouTube

What do yall think? i'll be installing the ARH long tubes next week hopefully.

 

[Blackram]

Sure sounds good. What all do you have done to her?

 

[Hemi450hp]

Your truck sounds like a beast. Those looked like a couple very strong runs.

 

[KLRpanda]

Sure sounds good. What all do you have done to her?

Your truck sounds like a beast. Those looked like a couple very strong runs.

Thanks matt The headers are going to make it all worth it!

Mod List is:

Afe Cold Air Intake
Ported and Polished Throttle Body
E-Fan
3000 Edge Stall Converter
Diablo Tuned
Whitelightning Trans Tune
Custom Engine Tune
2011 Rear Axle With the 4:11 LSD
Catless Mids Into a 18" MagnaFlow

-Mods Coming:
ARH 1 7/8 Long Tubes <-- These bad Boys are on there way to the house!
6.4 cam "not sure on this cam yet"
Valve Springs that will let me spin her up to about 6500 RPM
Port and polish job on the heads
Port match the intake
Bump up the conpression
and maybe switch to E85 if the tuning is avalible

-For the Track
15x3.5 front runners
16x10 rear wheel set up with Hoosier slicks

Should be able to break into the 12's with all the mods and some weight reduction. my goal is to beable to run a 12.9 N/A then I'll start spraying more than likely Best run so far in the truck is a 13.28 at 101mph on street tires. Hopig to make a better pass and be able to back the number up.

 

[SILVER_BULLET]

Thanks matt The headers are going to make it all worth it!

Mod List is:

Afe Cold Air Intake
Ported and Polished Throttle Body
E-Fan
3000 Edge Stall Converter
Diablo Tuned
Whitelightning Trans Tune
Custom Engine Tune
2011 Rear Axle With the 4:11 LSD
Catless Mids Into a 18" MagnaFlow

-Mods Coming:
ARH 1 7/8 Long Tubes <-- These bad Boys are on there way to the house!
6.4 cam "not sure on this cam yet"
Valve Springs that will let me spin her up to about 6500 RPM
Port and polish job on the heads
Port match the intake

-For the Track
15x3.5 front runners
16x10 rear wheel set up with Hoosier slicks

Should be able to break into the 12's with all the mods and some weight reduction. my goal is to beable to run a 12.9 N/A then I'll start spraying more than likely Best run so far in the truck is a 13.28 at 101mph on street tires. Hopig to make a better pass and be able to back the number up.

how are you getting the 15s to fit in the front if you dont mind me asking? im getting some 16x10s for the back and 16 front runners also but if its not to bad to get them to fit ill get 15s

 

[KLRpanda]

how are you getting the 15s to fit in the front if you dont mind me asking? im getting some 16x10s for the back and 16 front runners also but if its not to bad to get them to fit ill get 15s

A adapter from 5x5 to 5x4.5 bolt pattern it's what the guys were running when I still had my SRT10 some people frown on it but it works. I know with the weight off the front end and a few other places I'll beat the NA record.

Exact set up that my buddy justin is running on his SRT10
http://www.youtube.com/watch?v=JHj0jvlzUJA&feature=share&list=UU1mfD-wlgPPW7dUl-jmup5A

 

[SILVER_BULLET]

you have all the right mods im sure youll get it done for sure..im going for a 12 na also itll just be a while to get it but hopefully i get the wheels in soon im sure those will help out alot

 

[audio1der]

DUDE! Your truck sounds like a beast.
I'll just live vicariously through you & your mods if that's OK

 

[Big Boi]

What TB are your running?

 

[KLRpanda]

DUDE! Your truck sounds like a beast.
I'll just live vicariously through you & your mods if that's OK

perfectly fine! haha

What TB are your running?

I'm running a 88-89mm TB I ported and polished. Started out with a MOEs 87mm. Got a little tight on cash and sold it on the forum. So i did what any redneck would do. went over to a buddys house and borrowed a few of his tools and put a little sweat into it and then measured when i was happy with it the remaining metal is almost to thin though.

 

[joeshemi]

nice setup!

 

[BAILEY1]

It's a beast bro. Sounds great!

 

[joeshemi]

What are you doing as far as weight reduction klrpanda

 

[ZakkBaker]

Wow, nice videos!

 

[garner]

Sweet!

 

[TXKID]

Damn dude that thing hauls ass. Very nice

 

[URdone21]

That's a lotta mods. Jealous

 

[09SMOKINHEMI]

sounding very nice!!

 

[redsand]

Truck runs and sounds awesome, I love the sound of these with a good exhaust. Threw one on my ecoboost and lets just say it leaves much to be desired in the sound dept.