Some help here

[UNSTOPABLE]

Well guys i'm thinking buy a few things in december, but i'll like to listen your opinion..

What composition is better, next mouth i will be buy this products, but what is better option..??

MOE'S 85 or 87mm Throttle body..??
ARH Long Headers 1 3/4" or 1 7/8"..?? (Why is better)
And what catbak is better option..???

I wanna get's my truck in 14's down

Actually have VOLANT CAI, AIRAID SPACER, MAGNAFLOW 18" AND DIABLO INTUNE ON 91 OCT

I really apreciate it your support to make this possible...!!!

Thanks so much guys..!!!

 

[Arctic-Rodz]

well you don't need a spacer... waste of $.

is yours a single cab, quad or crew. 2x4 or 4x4. those things would help to know how far you need to go to get into the 14's but how far into the 14's do you wanna go?

 

[UNSTOPABLE]

well you don't need a spacer... waste of $.

is yours a single cab, quad or crew. 2x4 or 4x4. those things would help to know how far you need to go to get into the 14's but how far into the 14's do you wanna go?

Thanks man....

Ok... im sorry you are right my information is not complete......

Is single cab, 4x4 sport R/T, 5.7 liter.... i ll like to make a better time posible 14.1 or 13's. If is posible...

 

[Arctic-Rodz]

the mods you listed are good. I don't think you need a full cat back exhaust set up. a weld on unit will do.
the headers you listed are gonna be one of the best out there and will definitely do the job.
make sure you get a catch can installed if you don't have one yet.
87mm TB
3000 stall will help a lot

also, a custom tune from hemifever (for sure)

 

[UNSTOPABLE]

Thanks bro... i have a catch can just now....


The spacer still whit it or remove .?????
So, TB 87MM ...OK
The Long Header 1 3/4" or 1 7/8"..????

Thanks so much..!!!

 

[Darkflow]

Do you plan on a supercharger? I think that'll determine what size longtubes you want.

 

[Arctic-Rodz]

Do you plan on a supercharger? I think that'll determine what size longtubes you want.

this... otherwise the 1 3/4" will do. and you can just leave the spacer since you already have it on there.

 

[UNSTOPABLE]

Do you plan on a supercharger? I think that'll determine what size longtubes you want.

Thanks bro.....
no, i dont think so... i like more N/A... so for your commet, is better 1 3/4" right..????

 

[Darkflow]

Yeah 1 3/4 will be best. The 1 7/8 wouldn't really hurt you but they would perform better with more mods like a supercharger.

 

[UNSTOPABLE]

this... otherwise the 1 3/4" will do. and you can just leave the spacer since you already have it on there.

Ok... thanks so much.... so

87mm TB OK..!!
1 3/4" ARH Long tube headers Ok..!!
-You know Where i can find only tubes catback ( whitout muffler and tips)..???

Thanks for your support Guys..!!!!

 

[Arctic-Rodz]

what do you mean only tubes? like you want to run with no muffler? dump exhaust or what?

 

[UNSTOPABLE]

what do you mean only tubes? like you want to run with no muffler? dump exhaust or what?

No, i have right now a MAGNAFLOW 18" muffler and tips...
Only want to incresse a. Catback tube diameter at 2 1/2" inches..

Thanks..!!!

 

[Arctic-Rodz]

you should be fine with the stock exhaust diameter. I think after the muffler it has 2.5" pipes to the exhaust tips.

I think its 3" up to the muffler if im not mistaken. I have an 18" weld on magnaflow and it has a 3" inlet.

 

[UNSTOPABLE]

you should be fine with the stock exhaust diameter. I think after the muffler it has 2.5" pipes to the exhaust tips.

I think its 3" up to the muffler if im not mistaken. I have an 18" weld on magnaflow and it has a 3" inlet.

The stock diameter in catback after muffler is 2 1/4" ... and i wanna change to 2 1/2"
My muffler is 3" inlet and 2.5 outlet...whit 2.5" diameter tips... only i need a tubes alone

I tried to find only a tubes buy i can't .......

Thanks brothrr..!!!

 

[Darkflow]

No they don't offer just a kit for the mufflers back. Best bet would be to go custom. You can buy the mandrel bends online and just have a good local shop do it.

The MBRP catback exhaust isn't that expensive but idk what size the pipes are. If they are 2.5. I would say maybe try that and just swap tips and mufflers and sell the mbrp ones to make some money back but custom would be cheaper.

 

[UNSTOPABLE]

No they don't offer just a kit for the mufflers back. Best bet would be to go custom. You can buy the mandrel bends online and just have a good local shop do it.

The MBRP catback exhaust isn't that expensive but idk what size the pipes are. If they are 2.5. I would say maybe try that and just swap tips and mufflers and sell the mbrp ones to make some money back but custom would be cheaper.

You got it...!!!

I'll buy this cat back ...... thanks so much bro..!!!!!

 

[Hemi450hp]

Like the guys have said, the 87mm TB and a 1 3/4" ARH Longtubes is the best way to go. As for the exhaust, I would just leave it alone to be honest. You will not feel any difference in performance by only changing the piping behind the muffler. I would put that money towards a Hemifever custom tune instead.

 

[UNSTOPABLE]

Thanks man.... sorry but i have a cople a questions....
I decided for a DHR34WC (LONG TUBE 1 3/4" WHIT CATS) Will have a problem when intall this headers...???? My truck is 4x4 single cab... are those headers compatible whit my truck..???
And other cuestion.... came whit all necesary to install in my truck..???

Thanks a lot my friend

 

[Alfonsio]

well you don't need a spacer... waste of $.

is yours a single cab, quad or crew. 2x4 or 4x4. those things would help to know how far you need to go to get into the 14's but how far into the 14's do you wanna go?

I've never really understood why people put spacers in there...?

 

[UNSTOPABLE]

I've never really understood why people put spacers in there...?

#1 in my case because i like the whissle and #2 because i trust what the product offers, puts in there before




need experience on bad products.:!!!