autumnwalker
Senior Member
Truck is a (Canadian) 2015 Sport 1500.
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Truck is a (Canadian) 2015 Sport 1500.
Thanks! Did you have the always on issue with the M2 harness and the 2017 gear?I have been on this issue for some time since I installed the 2018 lid/hub assembly in my 2017 2500 as mentioned. I had Mikes harness in the past, but sold it when I got the 2018 stuff and as described, the panel light is always on, even when the truck is turned off. So given that, and the fact I have yet to cut/ move pins, I have lived with the “drain” issue and as of now, I have never had the battery drain to the point of experiencing a dead battery and couldn’t get the truck started. Now I don’t know how much juice I’m pulling, but not starting the truck for up to 6 days I haven’t had an issue. So I’m just leaving it alone (I have left my music jump drive in there too). Just my experience so far!
Yes, did not work unfortunately
Thanks! Did you have the always on issue with the M2 harness and the 2017 gear?
I am 100% certain that the light on my hub was off when the truck was on (key RUN, engine off) and that it came on when the truck went off. IIRC there was actually a delay and the HU popped on for a second (saw the RAM animation) and then went off - but the hub back light stayed on.
You can buy it from here:Need a adapter for my usb media hub in my 2014 Ram...
where can I get there ?
I have to go back out and reconnect the hub and see what it does ... maybe it turned on as a function of the new head unit being in the truck and learning the computer or something ... I dunno.No. It worked as it was supposed to. I didn’t want to try cutting the 2017 tray to fit the new 2018 hub, but Mikes harness worked perfectly as it supposed to. I have been holding off as I’m certainly not anywhere near skilled electrician/problem solver as many on this site. So I’ll live with the panel light on and hope it continues to not kill the battery and leave me stranded in Tim Buck Two here somewhere in Colorado.
I’m thinking of switching to this too. Did you have the dual usb in there before? Did you need the adapter because of upgrading to the UAS/UAQ? I think I say you had Android Auto working with usb-c do you know if CarPlay was also working ok with the usb-c?
Sent from my iPhone using Tapatalk
I had the USB/SD Card reader before which was not supported by the UAS I bought. Android Auto works great with USB-C to USB-C. I imagine carplay would work fine with USB-C to lightening or USB to lightening. I'll test it when I get a chance. My wife has an iPhone.
Ok cool thanks. I have a 2014 Ram but I bought a 2018 lid which has the harness needed already for the dual usb. Do you know if it’s the same harness for the usb-c outlets?
Sent from my iPhone using Tapatalk
Tried to find how to do a factory reset in enginering mode but it lools like a no go on the UAQ. have you pulled the fuse let it sit for a little bit. Then install the fuse cycle the key a few times and let it sit for a couple of hours untouched?After numerous attempts to correct the issue with my heated seat controls being greyed out, I am at an end. I could not fix it and have run out of options that I can see. I have tried all the configuration changes and options in AlphaOBD, received a new UAQ head unit, and even went as far as purchasing the module from infotainment.com for the MY 2014 trucks. Nothing has worked. My last thought would be maybe a software bug with the head unit but I doubt I would be able to correct that anyway as I don't have the VIN for the truck it cam from. Anyone else got any suggestions?
Yes, I have tried pulling batteries as well.Tried to find how to do a factory reset in enginering mode but it lools like a no go on the UAQ. have you pulled the fuse let it sit for a little bit. Then install the fuse cycle the key a few times and let it sit for a couple of hours untouched?
Can you send me the ID log from the BCM and the status & ID logs from the HSM?Yes, I have tried pulling batteries as well.
Sure just gotta figure out how to do that lol.Can you send me the ID log from the BCM and the status & ID logs from the HSM?
Sent from my SM-N986U using Tapatalk
Do you have the windows or android version of AlfaOBD?Sure just gotta figure out how to do that lol.
I have android version.
Attached is what I see. Buttons are there. Seats will even be on but I can't control them.
View attachment 235544